Arduino-Due mod for-GPIO-compatible-Raspberry-Pi
About the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi PCB
Arduino-Due mod for-GPIO-compatible-Raspberry-Pi is an open source AVR/Arduino PCB design by radioelf, published on GitHub. It is a 2-layer board measuring 78.3 × 43.3 mm, with 109 components from 47 distinct parts.
Its main chip is the ATMEGA16U2, from the AVR/Arduino family. Other key parts include the ATSAM3X8EA-AU, 74LVC1G125-SOT353, NCP1117ST33T3G and LMV358IDGKR. By type, the board carries 43 capacitors, 25 resistors, 8 diodes, 6 inductors, 5 ICs and 5 transistors.
From the project
PCB arduino Due para DuePi y Gpio Raspberry Pi
UNLESS OTHERWISE MUTUALLY AGREED TO BY THE PARTIES IN WRITING, LICENSOR OFFERS THE WORK AS-IS AND MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND CONCERNING THE WORK, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF TITLE, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT, OR THE ABSENCE OF LATENT OR OTHER DEFECTS, ACCURACY, OR THE PRESENCE OF ABSENCE OF ERRORS, WHETHER OR NOT DISCOVERABLE. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO SUCH EXCLUSION MAY NOT APPLY TO YOU. EXCEPT TO THE EXTENT REQUIRED BY…
Main components on the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi
Arduino-Due mod for-GPIO-compatible-Raspberry-Pi bill of materials (BOM)
109 components, 47 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATSAM3X8EA-AU | LQFP-144_20x20mm_Pitch0.5mm | IC1 |
| 1 | ATMEGA16U2 | MLF32-PAD | IC2 |
| 1 | 74LVC1G125-SOT353 | SC70-5 | IC3 |
| 1 | NCP1117ST33T3G | SOT-223 | IC4 |
| 1 | LMV358IDGKR | MSOP8 | U1 |
| 3 | FDN340P | SOT23-3 | Q1, Q2, Q4 |
| 1 | BC847 | SOT23-3 | Q3 |
| 1 | DMG2305 | SOT23-3 | Q5 |
| 1 | 12Mhz | Crystal_SMD_2520_4Pads | Y1 |
| 1 | 32.768Khz | Crystal_SMD_5032_2Pads | Y2 |
| 1 | 16Mhz | Crystal_SMD_2520_4Pads | Y3 |
| 1 | DronPi_GPIO | raspberrypi2 | J1 |
| 2 | USB-B-AB | USB_Micro-B | P1, P2 |
| 1 | ICSP1 | Pin_Header_Straight_2x03 | P3 |
| 2 | MF-MSMF050-2 500mA | Neosid_Inductor_SM-NE45_SMD1812 | F1, F2 |
| 1 | 0ZCA0035FF2G | Fuse_SMD1206_Wave | F3 |
| 1 | RESET | SW_SPST_B3S-1000 | SW1 |
| 1 | ERASE | SW_SPST_EVQPE1 | SW2 |
| 5 | CG0603MLC-05E | Neosid_Inductor_SM0603CG | VR1, VR2, VR3, VR4, VR5 |
| 1 | RX | LED_0603 | D1 |
Show 27 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TX | LED_0603 | D2 |
| 1 | CD1208 | D_0603 | D3 |
| 1 | SMBJ5V | DO-214AA | D4 |
| 1 | PESD0402-140 | C_0402 | D5 |
| 1 | 5v | LED_0603 | D6 |
| 1 | 3v3 | LED_0603 | D7 |
| 1 | Yellow | LED_0603 | D8 |
| 5 | MH2029-300Y | R_0805 | L1, L2, L3, L4, L5 |
| 1 | KNH16C104DA5TS | KYOCERA-KNH16-DA | L6 |
| 23 | 100nF | C_0402 | C1, C2, C3, C4, C5, C6, C9, C11 +15 |
| 8 | 10uF | C_1210_HandSoldering | C7, C8, C10, C18, C22, C35, C36, C40 |
| 2 | 10nF | C_0402 | C21, C34 |
| 7 | 22pF | C_0402 | C24, C25, C26, C27, C28, C29, C30 |
| 1 | 1uF | C_0402 | C33 |
| 1 | 47uF | C_1210_HandSoldering | C39 |
| 1 | 100uF | TantalC_SizeD_EIA-7343_Reflow | C42 |
| 3 | 100K | R_0402 | R1, R18, R20 |
| 1 | 0R | R_0402 | R2 |
| 2 | 39R | R_0402 | R3, R4 |
| 1 | 6k8 | R_0603 | R5 |
| 1 | 1M | R_0402 | R6 |
| 2 | 22R | R_0402 | R7, R8 |
| 4 | 10K | R_0402 | R9, R10, R13, R16 |
| 7 | 1K | R_0402 | R11, R12, R14, R15, R17, R22, R23 |
| 1 | 4k7 | R_0402 | R19 |
| 1 | 1K7 | R_0402 | R21 |
| 2 | 1K5 | R_0402 | R24, R25 |
Arduino-Due mod for-GPIO-compatible-Raspberry-Pi design files
The KiCad project lives in the radioelf/Arduino-Due-mod-for-GPIO-compatible-Raspberry-Pi repository on GitHub; these links point at the commit this page was built from.
- LayoutDuePi.kicad_pcb
Arduino-Due mod for-GPIO-compatible-Raspberry-Pi: common questions
What microcontroller does the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi use?
The Arduino-Due mod for-GPIO-compatible-Raspberry-Pi is built around the ATMEGA16U2, from the AVR/Arduino family.
How big is the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi PCB?
The Arduino-Due mod for-GPIO-compatible-Raspberry-Pi measures 78.3 × 43.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi?
109 components, from 47 distinct parts. The full bill of materials is listed on this page.
Where can I download the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi design files?
From the radioelf/Arduino-Due-mod-for-GPIO-compatible-Raspberry-Pi repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi design in my own project?
The repository has no license, so all rights stay with radioelf. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Arduino-Due mod for-GPIO-compatible-Raspberry-Pi without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k
AVR/ArduinoMegadesk
gcormier
41.7 × 32.2 mm23 parts2LGPL-3.0818
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746