76 open source boards using the NCP1117ST33T3G
Real designs built with the NCP1117ST33T3G, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Bldc control ver3
pekkaroi
98 × 38 mm61 parts2LGPL-2.0199AVR/Arduino
VGAtonic
dqydj
78.3 × 74.6 mm56 parts2LNo license133STM32
Bldc
mrkindustries
38.5 × 65 mm124 parts2LNo license112ESP32
ESP32BB
asukiaaa
43.2 × 61 mm27 parts2LNo license57STM32
QuadcopterSystem
vedderb
67 × 50 mm91 parts2LGPL-3.029RP2040/RP2350
Doom keycap hardware
rsheldiii
32.5 × 15.5 mm33 parts2LMIT21Quad serial breakout
jamesfowkes
50 × 50 mm44 parts2LNo license15MicroBBPS
stasiselectronics
54 × 24 mm21 parts2LNo license14Esp toggl
DirkHeinke
22.9 × 50.8 mm7 parts2LNo license12AVR/Arduino
EtherDue
freetronics
101.6 × 53.3 mm153 partsNo license11RP2040/RP2350
RP2040GPSTracker
justsem
99.6 × 53 mm128 parts2LCC-BY-SA-4.011Board-RZA1L
martinribelotta
85.5 × 79.9 mm144 parts4LNo license8Microchip SAM
OSSW - Open Scart Switch - Main
BinaryS010
401.6 × 130.1 mm310 parts4LGPL-3.07ESP32
PCBmain
MagnusLab
112 × 48.8 mm63 parts2LGPL-3.07ESP32
Esp32stack
asukiaaa
3.2 × 3.2 mm27 parts2LNo license7NXP
AD7124-4-Implementation
fedecastellaro
114.2 × 98.8 mm36 parts2LNo license5- schematic only · 170 parts
Yatagarasu red
DCoJA
170 partsCC-BY-SA-4.05 ESP8266
Hw trials
forGGe
49.5 × 49.5 mm28 parts2LNo license3Radio
hedj
65 × 56 mm89 parts2LGPL-2.02RP2040/RP2350
Billig
playlogo
86 × 74 mm58 parts2LTAPR-OHL-1.02AVR/Arduino
DIYduino
szdiy
68.6 × 53.3 mm35 parts2LCC-BY-SA-4.02AVR/Arduino
Atmega32
vedantjadhav304
66.8 × 46 mm23 parts2LNo license2STM32
Phase2-module
udaravima
130 × 90 mm172 parts4LGPL-3.01AVR/Arduino
Arduino-Due mod for-GPIO-compatible-Raspberry-Pi
radioelf
78.3 × 43.3 mm109 parts2LNo license1RP2040/RP2350
Mainboard
palthedog
280 × 150 mm106 parts4LNo license1RP2040/RP2350
NEMESIS
svdrecbd
97 × 55 mm68 parts4LApache-2.01RP2040/RP2350
EIT-Multiplexer
ErenErenel
76.6 × 79.4 mm49 parts2LCERN-OHL-S-2.01RP2040/RP2350
Cmsis dap rp2040
tnishinaga
50 × 34 mm47 parts2LNo license1RP2040/RP2350
Gitea kicad viewer
Vandewaetere
52 × 51 mm39 parts2LMIT1STM32
Panelized2
jumper385
74.9 × 98 mm30 parts2LNo license1RP2040/RP2350
Thesis limb module rigid
MichaelJ-SHSU
76.2 × 76.2 mm376 parts6LNo license0STM32
AEM-60DC8 V1.2
akhemka-cmd
122 × 87.6 mm350 parts2LNo license0RP2040/RP2350
Drone
WiktorKociuba
60.4 × 98.3 mm201 parts6LNo license0NXP
Edu ciaa nxp
AndyPecotche
85.8 × 137 mm183 parts2LBSD-3-Clause0NXP
Edu ciaa nxp
AndyPecotche
85.8 × 137 mm183 parts2LNo license0NXP
Edu ciaa nxp micropython
lmtreser
85.8 × 137 mm183 parts2LMIT0
How designs wire the NCP1117ST33T3G
Read from the KiCad layouts of 60 open source designs, one per repository: what each pin of the NCP1117ST33T3G connects to, and the resistors, capacitors and other passives placed on it.
- The VI pin has a decoupling capacitor on 42 of 60 designs, most often 10 µF (then 100 nF).
- The OUT_4 pin is tied to 3.3V on 19 of 31 designs (not connected on 10, a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_1pin 1 | Connected to: GND 97% | — |
| VOpin 2 | Connected to: 3.3V 88% | — |
| VIpin 3 | Connected to: 5V 92% |
|
| OUT_4pin 4 | Connected to: 3.3V 61% · not connected 32% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include To220 powerstage by rene-dev, Bldc control ver3 by pekkaroi, VGAtonic by dqydj and Bldc by mrkindustries.
The NCP1117ST33T3G in open source designs
The gallery holds 76 open source boards using the NCP1117ST33T3G from 61 GitHub repositories; a typical one measures about 68.6 × 60 mm and carries around 57 components.
76% are two-layer designs, the rest use four layers or more, and 41% carry an open source license.
The most starred is To220 powerstage by rene-dev.
Parts used alongside the NCP1117ST33T3G
Microcontrollers on boards using the NCP1117ST33T3G
What boards using the NCP1117ST33T3G are built for
NCP1117ST33T3G: common questions
Where can I find a NCP1117ST33T3G reference design?
Each of the 76 boards on this page is a real design using the NCP1117ST33T3G. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the NCP1117ST33T3G VI pin?
The VI pin has a decoupling capacitor on 42 of 60 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 60 open source designs using the NCP1117ST33T3G.
How is the NCP1117ST33T3G OUT_4 pin connected?
The OUT_4 pin is tied to 3.3V on 19 of 31 designs (not connected on 10, a signal on 2). Counted from the KiCad layouts of 60 open source designs using the NCP1117ST33T3G.
What parts are used alongside the NCP1117ST33T3G?
The RP2040, W25Q128JVSIQ, W25Q128JVS, NCP1117ST50T3G and LPC4337JBD144 appear in the most repositories here.
Which microcontrollers do boards using the NCP1117ST33T3G use?
Most are built on RP2040/RP2350 (30), STM32 (14), AVR/Arduino (8) and ESP32 (6).
How big is a typical board using the NCP1117ST33T3G?
The median is 68.6 × 60 mm, and 76% are two-layer designs.
What is the most popular open source board using the NCP1117ST33T3G?
By GitHub stars, To220 powerstage by rene-dev, with 979 stars.
Can I simulate one of these boards using the NCP1117ST33T3G before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.