CNC-BOT-DIBUJANTE
About the CNC-BOT-DIBUJANTE PCB
CNC-BOT-DIBUJANTE is an open source ESP32 PCB design by RawnerWeb, published on GitHub. It is a 2-layer board measuring 100 × 89.5 mm, with 17 components from 6 distinct parts.
Its main chip is the ESP32-DEVKIT-V1, from the ESP32 family. By type, the board carries 7 connectors, 3 diodes, 3 capacitors, 3 resistors and 1 IC.
It belongs with the robotics & motion designs in this gallery.
From the project
CNC - BOT DIBUJANTE
Main components on the CNC-BOT-DIBUJANTE
CNC-BOT-DIBUJANTE bill of materials (BOM)
17 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DEVKIT-V1 | MODULE_ESP32_DEVKIT_V1 | U1 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J2 |
| 6 | Screw_Terminal_01x03 | PinHeader_1x03_P2.54mm_Vertical | J5, J6, J7, J8, J9, J10 |
| 3 | LED | LED_D3.0mm_Horizontal_O6.35mm_Z10.0mm | D1, D2, D3 |
| 3 | C_Polarized_US | CP_Radial_D10.0mm_P5.00mm | C1, C2, C3 |
| 3 | R_US | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3 |
CNC-BOT-DIBUJANTE design files
The KiCad project lives in the RawnerWeb/CNC-BOT-DIBUJANTE repository on GitHub; these links point at the commit this page was built from.
CNC-BOT-DIBUJANTE: common questions
What microcontroller does the CNC-BOT-DIBUJANTE use?
The CNC-BOT-DIBUJANTE is built around the ESP32-DEVKIT-V1, from the ESP32 family.
How big is the CNC-BOT-DIBUJANTE PCB?
The CNC-BOT-DIBUJANTE measures 100 × 89.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CNC-BOT-DIBUJANTE?
17 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the CNC-BOT-DIBUJANTE design files?
From the RawnerWeb/CNC-BOT-DIBUJANTE repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the CNC-BOT-DIBUJANTE design in my own project?
The repository has no license, so all rights stay with RawnerWeb. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the CNC-BOT-DIBUJANTE without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k