HardLabs

RenewableRegulator MPPT PCB 2017

re-innovation·RenewableRegulator·PCB/RenewableRegulator_MPPT_PCB_2017/RenewableRegulator_MPPT_PCB_2017.kicad_pcb

RenewableRegulator MPPT PCB 2017 layout, top view — open source AVR/Arduino board by re-innovation

About the RenewableRegulator MPPT PCB 2017

RenewableRegulator MPPT PCB 2017 is an open source AVR/Arduino PCB design by re-innovation, published on GitHub under the MIT license. It is a board measuring 102 × 72 mm, with 54 components from 39 distinct parts.

Its main chip is the Arduino_Nano, from the AVR/Arduino family. Other key parts include the ACS712, LMR16006, MCP1702-50 and IR2117. By type, the board carries 16 capacitors, 10 resistors, 8 connectors, 7 diodes, 5 ICs and 2 inductors.

It belongs with the power & battery, displays & leds and sensors designs in this gallery.

From the project

Charge Regulator Designs for off-grid renewable energy projects. Series. Shunt. MPPT.

This is an open-source project to design a simple, low-cost, Charge Regulator Designs for off-grid renewable energy projects.

A charge-controller protects a re-chargeable battery from over (and sometime under) charging from a renewable energy resource.

This controller will work as a Series and Shunt controller. Future improvements include working as a Maximum Power Point Tracking. The design is based upon the Arduino IDE and will use one version of the Arduino processors (Arduino Nano initially). Voltage is measured using a potential divider. Current is measured using a hall-effect current…

Main components on the RenewableRegulator MPPT PCB 2017

ACS712LMR16006MCP1702-50IR2117

RenewableRegulator MPPT PCB 2017 bill of materials (BOM)

54 components, 39 distinct parts.

QtyPartRefs
2
ACS712
U1, U5
1
LMR16006
U2
1
MCP1702-50
U3
1
IR2117
U4
1
TK32A12N1
Q2
1
Arduino_Nano
J2
1
INPUT
P1
1
MicroSD
P3
1
OUTPUT
P5
1
TP_Vin
P8
1
TP_GND
P11
1
TP_5V
P12
1
TP_10V
P13
1
Encoder
ENC1
1
500mA
F1
2
VR
VR1, VR2
1
OLED_I2C
DISP1
2
3v3
D1, D2
3
1N5819
D3, D4, D9
1
DIODE
D10
Show 19 more
QtyPartRefs
1
1N5822
D11
1
22uH
L1
1
100µH
L2
5
100nf
C1, C2, C8, C12, C13
1
100uf
C3
1
2.2uf
C6
1
1uf
C7
1
1uf
C9
1
10uf
C10
1
1.6mF
C11
1
1mF
C14
2
1nf
C15, C17
2
0.1µF
C16, C18
2
Rb
R1, R3
2
Ra
R2, R4
1
4k7
R5
3
100k
R9, R10, R12
1
8.2k
R11
1
5
R13

RenewableRegulator MPPT PCB 2017 design files

The KiCad project lives in the re-innovation/RenewableRegulator repository on GitHub; these links point at the commit this page was built from.

RenewableRegulator MPPT PCB 2017: common questions

What microcontroller does the RenewableRegulator MPPT PCB 2017 use?

The RenewableRegulator MPPT PCB 2017 is built around the Arduino_Nano, from the AVR/Arduino family.

How big is the RenewableRegulator MPPT PCB 2017?

The RenewableRegulator MPPT PCB 2017 measures 102 × 72 mm and is 1.6002 mm thick.

How many components are on the RenewableRegulator MPPT PCB 2017?

54 components, from 39 distinct parts. The full bill of materials is listed on this page.

Where can I download the RenewableRegulator MPPT PCB 2017 design files?

From the re-innovation/RenewableRegulator repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the RenewableRegulator MPPT PCB 2017 design in my own project?

Yes, under the terms of its MIT license, which re-innovation chose for the repository.

Can I test firmware for the RenewableRegulator MPPT PCB 2017 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in RenewableRegulator

Similar boards