7 open source boards using the LMR16006
Real designs built with the LMR16006, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
MINI4
antonchromjak
65 × 18 mm151 parts4LNo license139AVR/Arduino
RenewableRegulator MPPT PCB 2017
re-innovation
102 × 72 mm54 partsMIT2ESP32
SBMS120
kitspace
170 × 120 mm269 parts4LNo license1STM32
SENTINEL-UHF T/R Module, 420-450 MHz, 300 W
ajisrawi
230 × 152 mm140 parts4LNo license0AVR/Arduino
RenewableRegulatorPCB 2017
re-innovation
101.4 × 90.8 mm53 partsMIT2Untitled
fharold
35.4 × 38.7 mm51 parts2LNo license0Buck Converter SubBoard 0-2
Govish
46.4 × 25.4 mm33 parts2LMIT0
How designs wire the LMR16006
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LMR16006 connects to, and the resistors, capacitors and other passives placed on it.
- The CB_1 pin has a series capacitor on 6 of 6 designs, most often 100 nF (then 220 nF).
- The SW_6 pin has a inductor on 6 of 6 designs, most often 22 µH (then 33 µH).
- The SW_6 pin has a series capacitor on 6 of 6 designs, most often 100 nF (then 220 nF).
- The FB_3 pin has a pull-up to 5V on 5 of 6 designs, most often 8 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CB_1pin 1 | Connected to: Signal 100% |
|
| GND_2pin 2 | Connected to: GND 100% | — |
| FB_3pin 3 | Connected to: Signal 100% |
|
| SHDN_4pin 4 | Connected to: Signal 67% · not connected 17% · 12V 17% |
|
| VIN_5pin 5 | Connected to: VDD 67% · a signal 33% |
|
| SW_6pin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MINI4 by antonchromjak, RenewableRegulator MPPT PCB 2017 by re-innovation, SBMS120 by kitspace and SENTINEL-UHF T/R Module, 420-450 MHz, 300 W by ajisrawi.
The LMR16006 in open source designs
The gallery holds 7 open source boards using the LMR16006 from 6 GitHub repositories; a typical one measures about 101.3 × 72 mm and carries around 54 components.
60% use four copper layers or more, and 43% carry an open source license.
The most starred is MINI4 by antonchromjak.
Microcontrollers on boards using the LMR16006
What boards using the LMR16006 are built for
LMR16006: common questions
Where can I find a LMR16006 reference design?
Each of the 7 boards on this page is a real design using the LMR16006. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LMR16006 CB_1 pin connected?
The CB_1 pin has a series capacitor on 6 of 6 designs, most often 100 nF (then 220 nF). Counted from the KiCad layouts of 6 open source designs using the LMR16006.
How is the LMR16006 SW_6 pin connected?
The SW_6 pin has a inductor on 6 of 6 designs, most often 22 µH (then 33 µH). Counted from the KiCad layouts of 6 open source designs using the LMR16006.
What pull-up resistor is used on the LMR16006 FB_3 pin?
The FB_3 pin has a pull-up to 5V on 5 of 6 designs, most often 8 kΩ (then 100 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR16006.
Which microcontrollers do boards using the LMR16006 use?
Most are built on AVR/Arduino (2), STM32 (2) and ESP32 (1).
How big is a typical board using the LMR16006?
The median is 101.3 × 72 mm, and 40% are two-layer designs.
What is the most popular open source board using the LMR16006?
By GitHub stars, MINI4 by antonchromjak, with 139 stars.
Can I simulate one of these boards using the LMR16006 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.