18 open source boards using the ACS712
Real designs built with the ACS712, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
C64 Saver addon board
bwack
43.9 × 29 mm42 parts2LCERN-OHL-1.2123STM32
Socket
eddyem
87 × 71 mm84 parts2LNo license80AVR/Arduino
UltrasonicSystem
Sonicators
145 × 110 mm81 parts2LNo license15ESP32
UPSMonitorStandalone rev01
enriquewph
100 × 70 mm103 parts2LMIT4AVR/Arduino
RenewableRegulator MPPT PCB 2017
re-innovation
102 × 72 mm54 partsMIT2STM32
SinglePhaseInverter
reljamar
190 × 91 mm156 parts4LMIT1Ganglia
H2O-Tnp
87 × 70 mm200 parts4LNo license0Microchip SAM
FanFDD
idlehandsdev
88 × 88 mm57 parts2LNo license0ESP32
Smarthome-Hardware
Dungeons-of-dragons
104.8 × 168.9 mm22 parts2LNo license0Current sensor-30A-ACS712-breakout hardware design
SolderedElectronics
38 × 22 mm21 parts2LTAPR-OHL-1.00STM32
BLDC-STM32
H2O-Tnp
69.9 × 59.7 mm162 parts4LNo license0Power Distribution
AUV-IITK
88.9 × 91.7 mm54 parts2LNo license3STM32
To220 powerstage
coon42
99.8 × 74.9 mm125 parts4LGPL-3.01STM32
To220 powerstage
rene-dev
99.8 × 74.9 mm125 parts4LGPL-3.0979STM32
To220 powerstage
emdotnet
99.8 × 74.9 mm125 parts4LGPL-3.00Current measurement extension board
stephaneamans
41.3 × 34.6 mm17 parts2LNo license0ESP32
Fuente Simetrica
EmersonEE
120.3 × 100 mm74 parts2LNo license0Power comsumption acs712
tuankiet65
51.4 × 16.5 mm5 parts2LNo license0
How designs wire the ACS712
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the ACS712 connects to, and the resistors, capacitors and other passives placed on it.
- The FILTER pin has a capacitor to GND on 15 of 15 designs, most often 1 nF (then 10 nF).
- The VCC pin has a decoupling capacitor on 12 of 15 designs, most often 100 nF.
- The IP+ pins have a series resistor on 9 of 17 designs, most often 4.7 kΩ (then 330 Ω).
- The VIOUT pin has a series resistor on 8 of 15 designs, most often 1 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IP+pin 1, 2 | Connected to: A connector 24% |
|
| GNDpin 5 | Connected to: GND 94% | — |
| FILTERpin 6 | Connected to: Signal 100% |
|
| VIOUTpin 7 | Connected to: A connector 20% |
|
| VCCpin 8 | Connected to: 5V 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include To220 powerstage by rene-dev, C64 Saver addon board by bwack, Socket by eddyem and UltrasonicSystem by Sonicators.
The ACS712 in open source designs
The gallery holds 18 open source boards using the ACS712 from 17 GitHub repositories; a typical one measures about 94.4 × 73.5 mm and carries around 78 components.
65% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is To220 powerstage by rene-dev.
Parts used alongside the ACS712
Microcontrollers on boards using the ACS712
What boards using the ACS712 are built for
ACS712: common questions
Where can I find a ACS712 reference design?
Each of the 18 boards on this page is a real design using the ACS712. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ACS712 FILTER pin connected?
The FILTER pin has a capacitor to GND on 15 of 15 designs, most often 1 nF (then 10 nF). Counted from the KiCad layouts of 17 open source designs using the ACS712.
What decoupling capacitors do designs use on the ACS712 VCC pin?
The VCC pin has a decoupling capacitor on 12 of 15 designs, most often 100 nF. Counted from the KiCad layouts of 17 open source designs using the ACS712.
What resistor goes on the ACS712 IP+ pin?
The IP+ pins have a series resistor on 9 of 17 designs, most often 4.7 kΩ (then 330 Ω). Counted from the KiCad layouts of 17 open source designs using the ACS712.
What parts are used alongside the ACS712?
The IR2184S, NCP1117ST33T3G, NCP1117ST50T3G, SI862x and STM32F105RC appear in the most repositories here.
Which microcontrollers do boards using the ACS712 use?
Most are built on STM32 (6), AVR/Arduino (3), ESP32 (3) and Microchip SAM (1).
How big is a typical board using the ACS712?
The median is 94.4 × 73.5 mm, and 65% are two-layer designs.
What is the most popular open source board using the ACS712?
By GitHub stars, To220 powerstage by rene-dev, with 979 stars.
Can I simulate one of these boards using the ACS712 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.