Metalclaw pico rp2

renzbagaporo·metalclaw-pico-rp2

Metalclaw pico rp2 PCB layout, top view — open source RP2040/RP2350 board by renzbagaporo

About the Metalclaw pico rp2 PCB

Metalclaw pico rp2 is an open source RP2040/RP2350 PCB design by renzbagaporo, published on GitHub under the CC-BY-SA-4.0 license. It is a 4-layer board measuring 21 × 51 mm, with 123 components from 24 distinct parts.

Its main chip is the RaspberryPi_Pico, from the RP2040/RP2350 family. Other key parts include the AP2112K-3.3TRG1, SC1512(13)-A4 and APS6404L-3SQR-SN. By type, the board carries 83 resistors, 29 capacitors, 3 ICs, 2 connectors, 2 switches and 1 module.

From the project

An RP2354B board for testing firmware on a Raspberry Pi Pico or Pico 2. Metalclaw firmware provides Python-controlled peripheral emulation and a USB debug probe. The carrier connects those functions to the target's GPIO, analogue inputs and SWD port.

An RP2354B board for testing firmware on a Raspberry Pi Pico or Pico 2. Metalclaw firmware provides Python-controlled peripheral emulation and a USB debug probe. The carrier connects those functions to the target's GPIO, analogue inputs and SWD port.

- Emulate I2C, SPI and UART devices connected to the target. - Generate and read digital signals on the target's exposed GPIOs. - Supply filtered PWM stimulus to its three ADC inputs. - Program and debug the target through SWD; control its reset and regulator enable.

Metalclaw pico rp2, from the project README
From the project README

Main components on the Metalclaw pico rp2

Metalclaw pico rp2 bill of materials (BOM)

123 components, 24 distinct parts.

QtyPartRefs
1
AP2112K-3.3TRG1
Diodes Incorporated
U1
1
SC1512(13)-A4
RP2354B
Raspberry Pi
U2
1
APS6404L-3SQR-SN
AP Memory
U3
1
RaspberryPi_Pico
Raspberry Pi
A1
1
ABM8-272-T3
Y1
1
HH 16P TYPE-C (Y495)
HH
J1
1
HC-PZ127-7.2L-2x5PS
HCTL
J2
2
YTS810SJM
YIYUAN
SW1, SW2
1
LMBR140ET1G
LRC
D1
1
3.3u
L1
2
10u
Samsung Electro-Mechanics
C1, C2
13
100n
Yageo
C3, C14, C15, C16, C17, C18, C19, C20 +5
3
1.5n
C4, C5, C6
3
10n
C7, C8, C9
5
GRM155R60J475ME47D
4.7u
Murata
C10, C11, C12, C13, C24
2
15p
C26, C27
1
1u
Samsung Electro-Mechanics
C28
27
5.1k
R1, R2, R3, R4, R5, R6, R7, R8 +19
4
1k
R18, R34, R42, R78
4
2.2k
R23, R24, R26, R83
Show 4 more
QtyPartRefs
3
330
R30, R31, R32
42
100
R33, R35, R36, R37, R38, R39, R40, R41 +34
1
33
R73
2
WR02X27R0FAL
27
Walsin
R80, R81

Metalclaw pico rp2 design files

The KiCad project lives in the renzbagaporo/metalclaw-pico-rp2 repository on GitHub; these links point at the commit this page was built from.

Metalclaw pico rp2: common questions

What microcontroller does the Metalclaw pico rp2 use?

The Metalclaw pico rp2 is built around the RaspberryPi_Pico, from the RP2040/RP2350 family.

How big is the Metalclaw pico rp2 PCB?

The Metalclaw pico rp2 measures 21 × 51 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Metalclaw pico rp2?

123 components, from 24 distinct parts. The full bill of materials is listed on this page.

Where can I download the Metalclaw pico rp2 design files?

From the renzbagaporo/metalclaw-pico-rp2 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Metalclaw pico rp2 design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which renzbagaporo chose for the repository.

Can I test firmware for the Metalclaw pico rp2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards