Uni dap v3
Reutronix·uni-dap-v3
About the Uni dap v3 PCB
Uni dap v3 is an open source STM32 PCB design by Reutronix, published on GitHub. It is a 4-layer board measuring 66.2 × 30.9 mm, with 147 components from 50 distinct parts.
Its main chip is the STM32F103CBTX, from the STM32 family. Other key parts include the C23380905, TPS62A02A, USBLC6-2P6, CY7C65634 and SN6505ADBV. By type, the board carries 54 capacitors, 50 resistors, 16 diodes, 10 ICs, 4 crystals and 3 transistors.
It belongs with the usb & debug tools designs in this gallery.
From the project
UniDAP hardware repo
Galvanically isolated CMSIS-DAP debug probe with USB-to-I²C/SPI/GPIO bridging.
UniDAP is an open hardware debug/programming probe. It combines a full USB-isolated CMSIS-DAP probe (SWD + UART) with a USB-to-I²C/SPI/GPIO bridge, so a single USB-C cable gives you target programming, a serial console, general-purpose bus access, and isolated power — all on the far side of a galvanic isolation barrier.

Main components on the Uni dap v3
Uni dap v3 bill of materials (BOM)
147 components, 50 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C23380905 ТРАР22811AW5 | SOT-23-5 | U301 |
| 1 | TPS62A02A | SOT-563 | U302 |
| 1 | USBLC6-2P6 | SOT-666 | U303 |
| 1 | CY7C65634 | QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U304 |
| 1 | SN6505ADBV | SOT-23-6 | U305 |
| 1 | ADUM4160 | SOIC-16W_7.5x10.3mm_P1.27mm | U306 |
| 1 | CH347F | QFN-28-1EP_4x4mm_P0.4mm_EP2.3x2.3mm | U307 |
| 1 | STM32F103CBTX STM32F103CBTx | LQFP-48_7x7mm_P0.5mm | U401 |
| 1 | XC8111AA018R-G | USP-6B06 | U501 |
| 1 | TXB0102DCU | VSSOP-8_2.3x2mm_P0.5mm | U502 |
| 1 | SS8550 | SOT-323_SC-70 | Q401 |
| 2 | DMG3415UFY4Q | DMG3415UFY4Q-7 | Q501, Q502 |
| 1 | 12MHZ 12MHz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y301 |
| 2 | 8MHZ 8MHz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y302, Y402 |
| 1 | 32.768kHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y401 |
| 1 | USB_C_RECEPTACLE_USB2.0_16PIN USB_C_Receptacle_USB2.0_16PIN | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J301 |
| 1 | CONN_ARM_JTAG_SWD_10 Conn_ARM_JTAG_SWD_10 | SAMTEC_FTSH-105-XX-X-DV | J501 |
| 1 | CONN_02X12_ODD_EVEN Conn_02x12_Odd_Even | PinHeader_2x12_P2.54mm_Vertical | J502 |
| 3 | TAC_SW_4P_6MM TAC_SW_4P_6mm | TS_6x6mm | SW401, SW402, SW403 |
| 1 | 750315240 | 750315240 | TR301 |
Show 30 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C264407 LED_RED | LED_0402 | D301 |
| 2 | MBR1020VL | D_SOD-123F | D302, D303 |
| 1 | C2980183 LED_GREEN | LED_0402 | D401 |
| 12 | ESD5V0B03-1006 | DFN1006-2_SMD0402 | D402, D403, D404, D405, D406, D407, D501, D502 +4 |
| 1 | 2.2UH 2.2uH | L_1008_2520Metric | L301 |
| 2 | C88990 120R@100MHz | L_0805_2012Metric | L302, L303 |
| 1 | 10nF | C_0402 | C301 |
| 27 | 100NF 100nF | C_0402 | C302, C305, C307, C309, C311, C312, C313, C314 +19 |
| 9 | 10UF 10uF | C_0603 | C303, C304, C306, C308, C310, C320, C324, C401 +1 |
| 4 | 4.7UF 4.7uF | C_0402 | C315, C316, C322, C329 |
| 1 | 100PF 100pF | C_0402 | C317 |
| 2 | 10PF 10pF | C_0402 | C318, C319 |
| 2 | 1UF 1uF | C_0402 | C321, C406 |
| 2 | 22PF 22pF | C_0402 | C333, C334 |
| 4 | 18PF 18pF | C_0402 | C407, C408, C411, C412 |
| 2 | 9pF | C_0402 | C409, C410 |
| 3 | 100K 100k | R_0402 | R301, R304, R314 |
| 1 | 453K 453k | R_0402 | R302 |
| 10 | 10K 10k | R_0402 | R303, R310, R313, R322, R323, R409, R415, R416 +2 |
| 2 | 5.1K 5.1k | R_0402 | R306, R307 |
| 6 | 0R | R_0402 | R308, R402, R502, R503, R504, R505 |
| 1 | 10M | R_0402 | R309 |
| 3 | 10k | R_0402 | R311, R312, R419 |
| 1 | 649R | R_0402 | R315 |
| 1 | 47.5K 47.5k | R_0402 | R316 |
| 6 | C106231 0R | R_0402 | R317, R414, R417, R501, R506, R507 |
| 7 | 22R | R_0402 | R318, R319, R320, R321, R410, R411, R412 |
| 3 | 4.7K 4.7k | R_0402 | R324, R407, R408 |
| 4 | 1.5K 1.5k | R_0402 | R401, R403, R404, R413 |
| 2 | 33R | R_0402 | R405, R406 |
Uni dap v3 design files
The KiCad project lives in the Reutronix/uni-dap-v3 repository on GitHub; these links point at the commit this page was built from.
- Layoutuni-dap.kicad_pcb
- Schematicuni-dap.kicad_sch
- BOMproduction/bom.csv
Uni dap v3: common questions
What microcontroller does the Uni dap v3 use?
The Uni dap v3 is built around the STM32F103CBTX, from the STM32 family.
How big is the Uni dap v3 PCB?
The Uni dap v3 measures 66.2 × 30.9 mm, has 4 copper layers and is 2.025 mm thick.
How many components are on the Uni dap v3?
147 components, from 50 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Uni dap v3 design files?
From the Reutronix/uni-dap-v3 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Uni dap v3 design in my own project?
The repository has no license, so all rights stay with Reutronix. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Uni dap v3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k