PicoWFanController

rmpel·PicoWFanController

PicoWFanController PCB layout, top view — open source Raspberry Pi board by rmpel

About the PicoWFanController PCB

PicoWFanController is an open source Raspberry Pi PCB design by rmpel, published on GitHub under the Custom license license. It is a 2-layer board measuring 37.5 × 150 mm, with 45 components from 28 distinct parts.

Its main chip is the RaspberryPi_Pico_W, from the Raspberry Pi family. Other key parts include the IP2721_MAX12. By type, the board carries 15 connectors, 15 resistors, 3 capacitors, 2 transistors, 1 IC and 1 module.

From the project

A small, quiet controller for a standard 4-wire PC fan, built around a Raspberry Pi Pico W. Designed for dual duty: solder-fume extractor on the bench, bedroom fan at night.

A small, quiet controller for a standard 4-wire PC fan, built around a Raspberry Pi Pico W. Designed for dual duty: solder-fume extractor on the bench, bedroom fan at night.

Control is by rotary encoder + push-button on the device itself, or over WiFi via a built-in web UI and REST API. A 10-segment LED bar shows the current speed at a glance.

- 25 kHz PWM drive, tachometer read-back, configurable PWM polarity - Rotary encoder with short-press, double-click and press-and-hold gestures - Predefined / boost / min speeds, configurable step size - 10-LED bar graph for speed, also used as…

Main components on the PicoWFanController

PicoWFanController bill of materials (BOM)

45 components, 28 distinct parts.

QtyPartRefs
1
IP2721_MAX12
U1
1
RaspberryPi_Pico_W
A1
2
Si2302 A2SHB GSD
Q1, Q2
1
Dell Fan
J1
1
Power
J2
1
USB_C_Receptacle_USB2.0_16P
J3
1
Power Select
J4
1
USB_C_Receptacle_USB2.0_16P
J5
10
Conn_01x05_Pin
J6, J7, J8, J9, J10, J11, J12, J13 +2
1
HDSP-4832_2
BAR1
1
IN+
BUCK1
1
OUT+
BUCK2
1
OUT-
BUCK3
1
IN-
BUCK4
1
RotaryEncoder_Switch_MP
SW1
1
Handwire from PiZero
TP2+3
1
1N5817
D1
1
1uF
C1
1
10uF
C2
1
0.1uF
C3
Show 8 more
QtyPartRefs
1
225
R1
4
250
R2, R3, R4, R5
3
362
R6, R7, R8
2
400
R9, R10
1
10K
R11
2
5K1
R12, R13
1
100K
R14
1
100
R15

PicoWFanController design files

The KiCad project lives in the rmpel/PicoWFanController repository on GitHub; these links point at the commit this page was built from.

PicoWFanController: common questions

What microcontroller does the PicoWFanController use?

The PicoWFanController is built around the RaspberryPi_Pico_W, from the Raspberry Pi family.

How big is the PicoWFanController PCB?

The PicoWFanController measures 37.5 × 150 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PicoWFanController?

45 components, from 28 distinct parts. The full bill of materials is listed on this page.

Where can I download the PicoWFanController design files?

From the rmpel/PicoWFanController repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the PicoWFanController design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

Can I test firmware for the PicoWFanController without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

Similar boards