InfinitiMirrorNutzen
About the InfinitiMirrorNutzen PCB
InfinitiMirrorNutzen is an open source ESP8266 PCB design by RT-CUSTOMZ, published on GitHub under the CC0-1.0 license. It is a 2-layer board measuring 90.4 × 90.3 mm, with 16 components from 11 distinct parts.
Its main chip is the ESP-12F, from the ESP8266 family. By type, the board carries 5 capacitors, 5 resistors, 1 transistor and 1 diode.
From the project
A small inifinity mirror using WLED on an ESP8266
InfinitiMirrorNutzen bill of materials (BOM)
16 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | FDN340P | SOT-23 | Q1 |
| 1 | 5V_In | PinSocket_1x01_P2.54mm_Vertical | 5V_IN |
| 1 | 5V | PinSocket_1x01_P2.54mm_Vertical | 5V_OUT |
| 1 | ESP-12F | ESP-12E | ESP8266 |
| 1 | LT1117-3.3 | SOT-223-3_TabPin2 | LM1337 |
| 1 | BZT52C6V8 | D_SOD-123F | D1 |
| 2 | 100nF | C_0805_2012Metric | C1, C3 |
| 2 | 10u | C_1206_3216Metric | C2, C4 |
| 1 | 330u | CP_Elec_6.3x7.7 | C5 |
| 4 | 10k | R_0805_2012Metric | R1, R2, R3, R4 |
| 1 | 100k | R_0805_2012Metric | R5 |
InfinitiMirrorNutzen design files
The KiCad project lives in the RT-CUSTOMZ/InfinityMirror repository on GitHub; these links point at the commit this page was built from.
InfinitiMirrorNutzen: common questions
What microcontroller does the InfinitiMirrorNutzen use?
The InfinitiMirrorNutzen is built around the ESP-12F, from the ESP8266 family.
How big is the InfinitiMirrorNutzen PCB?
The InfinitiMirrorNutzen measures 90.4 × 90.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the InfinitiMirrorNutzen?
16 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the InfinitiMirrorNutzen design files?
From the RT-CUSTOMZ/InfinityMirror repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the InfinitiMirrorNutzen design in my own project?
Yes, under the terms of its CC0-1.0 license, which RT-CUSTOMZ chose for the repository.
Can I test firmware for the InfinitiMirrorNutzen without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
More boards in InfinityMirror
Similar boards
ESP8266ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1k
ESP8266HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738
ESP8266RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506
ESP8266Goatgdo
32.9 × 53.3 mm23 parts2LMIT506
ESP8266RatGDO-OpenSource-Bare-ESP8266
55 × 82.7 mm20 parts2LMIT506
ESP8266Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398