Uyanik
rutubetsiz·uyanik·hardware/UYANIK.kicad_pcb
About the Uyanik PCB
Uyanik is an open source ESP32 PCB design by rutubetsiz, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 65 × 50 mm, with 19 components from 17 distinct parts.
Its main chip is the ESP32-DevKitC, from the ESP32 family. Other key parts include the RST OPT, PWR OPT and LED OPT. By type, the board carries 8 connectors, 4 ICs, 3 switches, 3 resistors and 1 diode.
It belongs with the iot & wireless designs in this gallery.
From the project
Remote PC Power Control
A device for turning a remote computer on and off. As long as you have internet access, it doesn’t matter where in the world you are. ## Why did I build this?
It started as a summer project. I had turned a spare computer into a server, but I didn’t want to leave it running all the time. University was about to start, and I needed a way to turn it on and off remotely. Shutting down a remote machine is easy, turning it on is not. Wake-on-LAN isn’t enough, and if you’re behind CGNAT on top of that... The answer to all of it was a device that stays on at home, so I built one. Wherever I am…

Main components on the Uyanik
Uyanik bill of materials (BOM)
19 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RST OPT | DIP-4_W7.62mm | U2 |
| 1 | ESP32-DevKitC | ESP32-DevKitC | U3 |
| 1 | PWR OPT | DIP-4_W7.62mm | U4 |
| 1 | LED OPT | DIP-4_W7.62mm | U5 |
| 1 | POWER SW+ | PinHeader_1x01_P2.54mm_Vertical | J1 |
| 1 | POWER SW- | PinHeader_1x01_P2.54mm_Vertical | J2 |
| 1 | RESET SW+ | PinHeader_1x01_P2.54mm_Vertical | J3 |
| 1 | RESET SW- | PinHeader_1x01_P2.54mm_Vertical | J4 |
| 1 | POWER LED+ | PinHeader_1x01_P2.54mm_Vertical | J5 |
| 1 | POWER LED- | PinHeader_1x01_P2.54mm_Vertical | J6 |
| 1 | VSS | PinHeader_1x01_P2.54mm_Vertical | J13 |
| 1 | VCC | PinHeader_1x01_P2.54mm_Vertical | J14 |
| 1 | SW_RESET | SW_PUSH_1P1T_6x3.5mm_H4.3_APEM_MJTP1243 | SW1 |
| 1 | SW_POWER | SW_PUSH_1P1T_6x3.5mm_H4.3_APEM_MJTP1243 | SW2 |
| 1 | ON / OFF | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW3 |
| 1 | POWER LED | LED_D5.0mm | D1 |
| 3 | 470 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3 |
Uyanik design files
The KiCad project lives in the rutubetsiz/uyanik repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/UYANIK.kicad_pcb
- Schematichardware/UYANIK.kicad_sch
Uyanik: common questions
What microcontroller does the Uyanik use?
The Uyanik is built around the ESP32-DevKitC, from the ESP32 family.
How big is the Uyanik PCB?
The Uyanik measures 65 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Uyanik?
19 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the Uyanik design files?
From the rutubetsiz/uyanik repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Uyanik design in my own project?
Yes, under the terms of its GPL-3.0 license, which rutubetsiz chose for the repository.
Can I test firmware for the Uyanik without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k