Atmega328p devboard
sam-james-harding·atmega328p-devboard·rev_2/devboard/devboard.kicad_pcb
About the Atmega328p devboard PCB
Atmega328p devboard is an open source AVR/Arduino PCB design by sam-james-harding, published on GitHub under the MIT license. It is a 2-layer board measuring 26.4 × 50.7 mm, with 26 components from 18 distinct parts.
Its main chip is the ATMEGA328P-A, from the AVR/Arduino family. Other key parts include the MCP2221A-I/ST and MCP1825S. By type, the board carries 6 resistors, 5 capacitors, 4 connectors, 4 diodes, 3 ICs and 3 switches.
It belongs with the dev boards & breakouts and usb & debug tools designs in this gallery.
From the project
This is my own custom development board, made for the ATmega328P. I created this both as learning experience (in PCB design and in soldering SMD components), and as a practical device to assist in prototyping.

Main components on the Atmega328p devboard
Atmega328p devboard bill of materials (BOM)
26 components, 18 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA328P-A ATmega328P-A | TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | MCP2221A-I/ST Microchip | TSSOP-14_4.4x5mm_P0.65mm | U2 |
| 1 | MCP1825S | SOT-223-3_TabPin2 | U3 |
| 1 | CRYSTAL_GND24 Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | USB_C_RECEPTACLE_USB2.0_16P USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | AVR-ISP-6 | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 2 | CONN_01X15_PIN Conn_01x15_Pin | PinHeader_1x15_P2.54mm_Vertical | J3, J4 |
| 1 | Pushbutton | SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 2 | SPDT | slide_switch | SW2, SW3 |
| 1 | D_Schottky | D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 2 | YELLOW | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D3 |
| 1 | LED_RED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 2 | 10PF 10pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | 4.7UF 4.7uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4 |
| 1 | 1UF 1uF KEMET | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 3 | 470R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R4 |
| 2 | 5K1 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6 |
Atmega328p devboard design files
The KiCad project lives in the sam-james-harding/atmega328p-devboard repository on GitHub; these links point at the commit this page was built from.
Atmega328p devboard: common questions
What microcontroller does the Atmega328p devboard use?
The Atmega328p devboard is built around the ATMEGA328P-A, from the AVR/Arduino family.
How big is the Atmega328p devboard PCB?
The Atmega328p devboard measures 26.4 × 50.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Atmega328p devboard?
26 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Atmega328p devboard design files?
From the sam-james-harding/atmega328p-devboard repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Atmega328p devboard design in my own project?
Yes, under the terms of its MIT license, which sam-james-harding chose for the repository.
Can I test firmware for the Atmega328p devboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k