Calculator
sauravraj67·Calculator·PCB/Calculator.kicad_pcb
About the Calculator PCB
Calculator is an open source Raspberry Pi PCB design by sauravraj67, published on GitHub. It is a 2-layer board measuring 124 × 136 mm, with 43 components from 6 distinct parts.
Its main chip is the RaspberryPi_Pico_W, from the Raspberry Pi family. Other key parts include the CEG003400. By type, the board carries 20 switches, 20 diodes, 1 IC and 1 module.
It belongs with the keyboards and displays & leds designs in this gallery.
From the project
I made a simple Calculator design. The concept is based on Raspberry Pi Pico , It has 19 Mechanical switches directly attached to the raspberry Pi Pico. A rotor encoder whose rotor would be used to change position the position of the cursor and it's button would be used to clean
I made a simple Calculator design. The concept is based on Raspberry Pi Pico , It has 19 Mechanical switches directly attached to the raspberry Pi Pico. A rotor encoder whose rotor would be used to change position the position of the cursor and it's button would be used to clean the screen And The Screen would be a 16X2 LCD Display with I2C
The firmware was written in C using the Raspberry Pi Pico SDK.
Main components on the Calculator
Calculator bill of materials (BOM)
43 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CEG003400 | MODULE_CEG003400 | U1 |
| 1 | RaspberryPi_Pico_W | RaspberryPi_Pico_Common_THT | A1 |
| 1 | WC1602A | WC1602A | DS1 |
| 19 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW5, SW6, SW7, SW8, SW9 +11 |
| 1 | RotaryEncoder_Switch_MP | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW4 |
| 20 | 1N4148 | D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2, D3, D4, D5, D6, D7, D8 +12 |
Calculator design files
The KiCad project lives in the sauravraj67/Calculator repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/Calculator.kicad_pcb
- SchematicPCB/Calculator.kicad_sch
- BOMBOM.csv
Calculator: common questions
What microcontroller does the Calculator use?
The Calculator is built around the RaspberryPi_Pico_W, from the Raspberry Pi family.
How big is the Calculator PCB?
The Calculator measures 124 × 136 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Calculator?
43 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Calculator design files?
From the sauravraj67/Calculator repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Calculator design in my own project?
The repository has no license, so all rights stay with sauravraj67. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Calculator without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507