Hot info orbs
scottdube·hot-info-orbs·hardware/hot-info-orbs-xiao-46mm/hot_info_orbs_xiao_46mm.kicad_pcb
About the Hot info orbs PCB
Hot info orbs is an open source ESP32 PCB design by scottdube, published on GitHub under the AGPL-3.0 license. It is a 2-layer board measuring 224 × 52.8 mm, with 12 components from 6 distinct parts.
Its main chip is the XIAO ESP32-S3 Plus, from the ESP32 family. By type, the board carries 3 switches, 2 capacitors, 1 IC and 1 resistor.
It belongs with the displays & leds designs in this gallery.
From the project
ESP32 desk widget driving five 1.28in round GC9A01 TFTs over one SPI bus
Copy of hardware/hot-info-orbs-xiao/ made 2026-10-19 (from branch enclosure-front-mockup, 318e8b0) with one physical change: the five displays sit 46.0 mm centre to centre instead of ~38.98 mm, to match the enclosure front in Fusion (mainbodyfront: bezel centres at 32.75 + n × 46.0; see docs/ENCLOSURE.md). The enclosure grows out of this board; this board is the one going to the fab. The original project left main on 2026-10-25 and is at tag board-xiao-narrow-final.
Main components on the Hot info orbs
Hot info orbs bill of materials (BOM)
12 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO ESP32-S3 Plus | XIAO-ESP32-S3-SOCKET | U2 |
| 5 | GC9A01_TFT | GC9A01_SOCKET | DS1, DS2, DS3, DS4, DS5 |
| 3 | SW_Push | SW_Tactile_SPST_Angled_PTS645Vx39-2LFS | SW1, SW2, SW3 |
| 1 | 100uF 16V | CP_Radial_D6.3mm_P2.50mm | C1 |
| 1 | 1u | C_Disc_D5.0mm_W2.5mm_P5.00mm | C2 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
Hot info orbs design files
The KiCad project lives in the scottdube/hot-info-orbs repository on GitHub; these links point at the commit this page was built from.
Hot info orbs: common questions
What microcontroller does the Hot info orbs use?
The Hot info orbs is built around the XIAO ESP32-S3 Plus, from the ESP32 family.
How big is the Hot info orbs PCB?
The Hot info orbs measures 224 × 52.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Hot info orbs?
12 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Hot info orbs design files?
From the scottdube/hot-info-orbs repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Hot info orbs design in my own project?
Yes, under the terms of its AGPL-3.0 license, which scottdube chose for the repository.
Can I test firmware for the Hot info orbs without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k