USB Tinnitus Audio Switch

Servacek·tinytus·hardware/usb-relay-audio-switch/rev01/relay.kicad_pcb

USB Tinnitus Audio Switch PCB layout, top view — open source AVR/Arduino board by Servacek

About the USB Tinnitus Audio Switch PCB

USB Tinnitus Audio Switch is an open source AVR/Arduino PCB design by Servacek, published on GitHub. It is a 2-layer board measuring 71.5 × 23 mm, with 22 components from 14 distinct parts.

Its main chip is the ATTINY85-20P, from the AVR/Arduino family. Other key parts include the TLV75533PDBV and TS5A23157DGS. By type, the board carries 10 resistors, 4 capacitors, 3 ICs, 3 diodes, 1 transistor and 1 connector.

It belongs with the audio and rf & radio designs in this gallery.

From the project

Tiny C99 library which allows you to use existing audio channels for digital transmission. The project was presented and defended at the national round of the SOČ competition and at the TMR UNIZA competition.

Small, modular C99 library for transmitting digital data over acoustic channels using FSK modulation. Targets desktop (Windows, Linux), WebAssembly, and embedded platforms.

- GFSK modulation - configurable bits-per-symbol (1, 2, 4, 8), frequency range, sample rate and symbol rate - Reed-Solomon ECC - configurable error correction percentage per frame - DSS scrambling - optional data scrambling before encoding - AGC - automatic gain control on the receive path - Sync detection - marker-based start/end-of-frame detection - Builds as an executable, static lib, DLL, or WASM module - PortAudio…

USB Tinnitus Audio Switch, from the project README
From the project README

Main components on the USB Tinnitus Audio Switch

USB Tinnitus Audio Switch bill of materials (BOM)

22 components, 14 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TLV75533PDBV
U1
1
TS5A23157DGS
U2
1
ATTINY85-20P
ATtiny85-20P
U3
1
2N7002
Q1
1
MJ-3502
J2
3
LED
D1, D2, D3
2
1UF
1uF
C1, C2
1
1NF
1nF
C3
1
100NF
100nF
C5
1
5K1
R1
2
47R
R2, R3
2
10K
R4, R8
1
220R
R5
4
1K5
R7, R9, R10, R11

USB Tinnitus Audio Switch design files

The KiCad project lives in the Servacek/tinytus repository on GitHub; these links point at the commit this page was built from.

USB Tinnitus Audio Switch: common questions

What microcontroller does the USB Tinnitus Audio Switch use?

The USB Tinnitus Audio Switch is built around the ATTINY85-20P, from the AVR/Arduino family.

How big is the USB Tinnitus Audio Switch PCB?

The USB Tinnitus Audio Switch measures 71.5 × 23 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the USB Tinnitus Audio Switch?

22 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the USB Tinnitus Audio Switch design files?

From the Servacek/tinytus repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the USB Tinnitus Audio Switch design in my own project?

The repository has no license, so all rights stay with Servacek. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the USB Tinnitus Audio Switch without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in tinytus

Similar boards