Antenna analyzer
shabaz123·antenna-analyzer·kicad-source/main-board/antenna-analyzer.kicad_pcb
About the Antenna analyzer PCB
Antenna analyzer is an open source PCB design by shabaz123, published on GitHub. It is a 2-layer board measuring 80 × 60 mm, with 33 components from 20 distinct parts.
By type, the board carries 8 resistors, 6 capacitors, 5 connectors, 3 diodes, 2 test points and 1 module.
It belongs with the rf & radio designs in this gallery.
From the project
There's a 4-position rotary selector knob. By using that, it is possible to select SWR or R/Z modes, and observe these values on the built-in moving-coil meter movement. The meter is fitted with a detailed scale, although the diagram here just shown LO/HI.
There's a 4-position rotary selector knob. By using that, it is possible to select SWR or R/Z modes, and observe these values on the built-in moving-coil meter movement. The meter is fitted with a detailed scale, although the diagram here just shown LO/HI.
(1) Connect a low-power HF source to the RF input on the instrument, and ensure that nothing is attached to the antenna connector (to simulate a bad antenna)

Antenna analyzer bill of materials (BOM)
33 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 100uA | wire-pads-2way | M1 |
| 2 | ~ | PinHeader_1x08_P2.54mm_Vertical | J1, J2 |
| 2 | ~ | PinHeader_1x04_P2.54mm_Vertical | J3, J4 |
| 1 | 5k LIN | Potentiometer_RD701F | P1 |
| 1 | ~ | mousebites-metric-5-trackgap | H5 |
| 3 | ~ | mousebites-metric-5 | H6, H7, H9 |
| 1 | wire-link-shorted | wire-link-12mm | LINK1 |
| 1 | RF INPUT 2W MAX BNC Socket | BNC Socket Edge 031-221-RFX | SK3 |
| 1 | ANTENNA N Socket | N Socket Edge 1-1337417-0 | SK4 |
| 1 | RS1010-2Pole-4Pos | RS1010 | SW1 |
| 2 | 10k | Potentiometer_Trimmer_Generic_Vertical | TP1, TP2 |
| 3 | 1N5711 | D_SOD-123 | D1, D2, D3 |
| 3 | 470p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3 |
| 3 | 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5, C6 |
| 3 | 3 x 150R Parallel | 1206-triple-parallel | R1, R2, R3 |
| 1 | 15k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 1 | 27k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 56k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 470R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
Antenna analyzer design files
The KiCad project lives in the shabaz123/antenna-analyzer repository on GitHub; these links point at the commit this page was built from.
Antenna analyzer: common questions
How big is the Antenna analyzer PCB?
The Antenna analyzer measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Antenna analyzer?
33 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Antenna analyzer design files?
From the shabaz123/antenna-analyzer repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Antenna analyzer design in my own project?
The repository has no license, so all rights stay with shabaz123. Use it as a reference, and ask the author before reusing the design.
More boards in antenna-analyzer
Similar boards
Hat
pa3gsb
65 × 56 mm81 parts2LNo license675Radioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675Radioberry preamp
pa3gsb
65 × 56 mm137 parts2LNo license675Goodwatch20
travisgoodspeed
25.6 × 27.6 mm20 parts2LNo license568GoodPocketWatch
travisgoodspeed
75.2 × 101.2 mm56 parts2LNo license568Goodwatch31
travisgoodspeed
25.6 × 27.6 mm23 parts2LNo license568