Madpad
shift-xd·Madpad·PCB/MADPAD.kicad_pcb
About the Madpad PCB
Madpad is an open source RP2040/RP2350 PCB design by shift-xd, published on GitHub. It is a 2-layer board measuring 63.4 × 81 mm, with 11 components from 3 distinct parts.
Its main chip is the XIAO-RP2040-DIP, from the RP2040/RP2350 family. By type, the board carries 9 switches, 1 IC and 1 connector.
It belongs with the displays & leds designs in this gallery.
From the project
My take on hackpad
- Seeed XIAO RP2040 microcontroller - 0.91" I2C OLED display - 3x3 mechanical key layout - Direct wiring for every key
This shows the full assembly of MADPAD in Fusion 360. It demonstrates how the PCB, case, and components fit together.
The schematic was designed in KiCad. Each switch connects directly to the RP2040. The OLED follows GND, VCC, SCL, SDA pin order.
Main components on the Madpad
Madpad bill of materials (BOM)
11 components, 3 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-RP2040-DIP | XIAO-RP2040-DIP | U1 |
| 1 | Conn_01x04 | SSD1306-0.91-OLED-4pin-128x32 | J1 |
| 9 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +1 |
Madpad design files
The KiCad project lives in the shift-xd/Madpad repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/MADPAD.kicad_pcb
- SchematicPCB/MADPAD.kicad_sch
Madpad: common questions
What microcontroller does the Madpad use?
The Madpad is built around the XIAO-RP2040-DIP, from the RP2040/RP2350 family.
How big is the Madpad PCB?
The Madpad measures 63.4 × 81 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Madpad?
11 components, from 3 distinct parts. The full bill of materials is listed on this page.
Where can I download the Madpad design files?
From the shift-xd/Madpad repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Madpad design in my own project?
The repository has no license, so all rights stay with shift-xd. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Madpad without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k