Rust board
shimo8810·rust-board·electronics/clock/clock.kicad_pcb
About the Rust board
Rust board is an open source AVR/Arduino PCB design by shimo8810, published on GitHub under the MIT license. It is a 2-layer board measuring 91.4 × 53.3 mm, with 53 components from 16 distinct parts.
Its main chip is the ATTINY2313-20P, from the AVR/Arduino family. Other key parts include the 74HC595 and 74HC165. By type, the board carries 27 resistors, 8 switches, 5 transistors, 5 capacitors, 3 ICs and 2 connectors.
From the project
Hobby board implemented in Rust
This project is intended for my personal study and information sharing. The main objectives are as follows:
Being a complete novice in circuit design, I created a simple hobby board for the purpose of studying circuit and PCB design.
The knowledge of developing embedded systems using Rust are scattered, so I wanted to compile information for myself. While there is a wealth of development information available for well-known boards, there is limited knowledge on directly controlling microcontrollers.

Main components on the Rust board
Rust board bill of materials (BOM)
53 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATTINY2313-20P ATtiny2313-20P | DIP-20_W7.62mm | U1 |
| 1 | 74HC595 | DIP-16_W7.62mm | U2 |
| 1 | 74HC165 | DIP-16_W7.62mm | U3 |
| 5 | 2SC1815 | TO-92_Inline | Q1, Q2, Q3, Q4, Q5 |
| 1 | 16 MHz | Crystal_HC18-U_Vertical | Y1 |
| 1 | CONN_02X03_COUNTER_CLOCKWISE Conn_02x03_Counter_Clockwise | PinHeader_2x03_P2.54mm_Vertical | J1 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J2 |
| 1 | Speaker | Buzzer_TDK_PS1240P02BT_D12.2mm_H6.5mm | LS1 |
| 8 | SW_Push | SW_PUSH_6mm_H5mm | SW2, SW3, SW4, SW5, SW6, SW7, SW8, SW9 |
| 1 | OSL40391-LRA | OSL40391-LRA | D1 |
| 3 | 0.1U 0.1u | C_Disc_D3.0mm_W1.6mm_P2.50mm | C1, C4, C5 |
| 2 | 22P 22p | C_Disc_D3.0mm_W1.6mm_P2.50mm | C2, C3 |
| 8 | 330 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8 |
| 5 | 10K 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R10, R11, R12, R26 |
| 5 | 3.9K 3.9k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R13, R14, R15, R16, R27 |
| 9 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R17, R18, R19, R20, R21, R22, R23, R24 +1 |
Rust board design files
The KiCad project lives in the shimo8810/rust-board repository on GitHub; these links point at the commit this page was built from.
Rust board: common questions
What microcontroller does the Rust board use?
The Rust board is built around the ATTINY2313-20P, from the AVR/Arduino family.
How big is the Rust board?
The Rust board measures 91.4 × 53.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Rust board?
53 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Rust board design files?
From the shimo8810/rust-board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Rust board design in my own project?
Yes, under the terms of its MIT license, which shimo8810 chose for the repository.
Can I test firmware for the Rust board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k