7 open source boards using the ATtiny2313-20P

Real designs built with the ATtiny2313-20P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the ATtiny2313-20P

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATtiny2313-20P connects to, and the resistors, capacitors and other passives placed on it.

PD1pin 3Connected to: Signal 83% · not connected 17%
  • Series resistor on 33% · 10 kΩ (1), 470 Ω (1)
PD3pin 7Connected to: Signal 100%
  • Series resistor on 33% · 470 Ω (1), 3.9 kΩ (1)
PD4pin 8Connected to: Signal 100%
  • Series resistor on 33% · 470 Ω (1), 3.9 kΩ (1)
PD5pin 9Connected to: Signal 100%
  • Series resistor on 33% · 470 Ω (1), 3.9 kΩ (1)
GNDpin 10Connected to: GND 67% · a signal 33%
PD6pin 11Connected to: Signal 83% · not connected 17%
  • Series resistor on 33% · 470 Ω (1), 3.9 kΩ (1)
PB4pin 16Connected to: Signal 100%
  • Pull-up to VCC on 33% · 1 kΩ (1), 470 Ω (1)
  • Series resistor on 33% · 470 Ω (1), 1 kΩ (1)
PB5pin 17Connected to: A connector 67%, the microcontroller 33%
  • Pull-up to VCC on 33% · 1 kΩ (1), 470 Ω (1)
VCCpin 20Connected to: VCC 67% · a signal 33%
  • Decoupling capacitor on 33% · 100 nF (3)

11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RescueAVRAdapter by felias-fogg, Fakedeck gerber by syuchan1005, C64UserPortMidi by relic-se and C128DKEYBOARD by danwerner21.

The ATtiny2313-20P in open source designs

The gallery holds 7 open source boards using the ATtiny2313-20P from 7 GitHub repositories; a typical one measures about 89.7 × 77.7 mm and carries around 25 components.

100% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.

The most starred is RescueAVRAdapter by felias-fogg.

Microcontrollers on boards using the ATtiny2313-20P

ATtiny2313-20P: common questions

Where can I find a ATtiny2313-20P reference design?

Each of the 7 boards on this page is a real design using the ATtiny2313-20P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

Which microcontrollers do boards using the ATtiny2313-20P use?

Most are built on AVR/Arduino (6) and RP2040/RP2350 (1).

How big is a typical board using the ATtiny2313-20P?

The median is 89.7 × 77.7 mm, and 100% are two-layer designs.

What is the most popular open source board using the ATtiny2313-20P?

By GitHub stars, RescueAVRAdapter by felias-fogg, with 56 stars.

Can I simulate one of these boards using the ATtiny2313-20P before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part