FrostChain-ESkin-Crate
shubhamFoT·FrostChain-ESkin-Crate·02_electronics/kicad/FrostChain_ESkin_Crate.kicad_sch
About the FrostChain-ESkin-Crate PCB
FrostChain-ESkin-Crate is an open source ESP32 PCB design by shubhamFoT, published on GitHub under the MIT license. It is a board, with 36 components from 34 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the MPPT charger, 4S LiFePO4, CV 14.4 V, LM2596-5.0, Sipeed Tang Nano 9K (Gowin GW1NR-9), SIM7600-class 5G/LTE + GNSS modem and 12 V -> 4.0 V buck, 3 A. By type, the board carries 11 resistors, 8 ICs, 5 capacitors, 2 antennas, 1 transistor and 1 connector.
It belongs with the power & battery designs in this gallery.
Main components on the FrostChain-ESkin-Crate
FrostChain-ESkin-Crate bill of materials (BOM)
36 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MPPT charger, 4S LiFePO4, CV 14.4 V | U1 | |
| 1 | LM2596-5.0 | U2 | |
| 1 | Sipeed Tang Nano 9K (Gowin GW1NR-9) | U3 | |
| 1 | ESP32-S3 | U4 | |
| 1 | SIM7600-class 5G/LTE + GNSS modem | U5 | |
| 1 | 12 V -> 4.0 V buck, 3 A | U6 | |
| 1 | SHT31 | U7 | |
| 1 | BTS7960 module (IBT-2), 43 A half-bridge | U8 | |
| 1 | 2N7002 | SOT-23 | Q1 |
| 1 | Fan tach input (verify pinout) | J1 | |
| 1 | 5G/LTE MAIN | AE1 | |
| 1 | GNSS (GPS) | AE2 | |
| 1 | 4S BMS, 12.8 V 6 Ah LiFePO4 + BMS | BT1 | |
| 1 | 10 A | F1 | |
| 1 | 30 W flex | PV1 | |
| 1 | TEC1-12706 (12 V, 6 A max) | TEC1 | |
| 1 | 100k NTC | TH1 | |
| 1 | 10k NTC hot-side (assumed) | TH2 | |
| 1 | SS34 | D_SMA | D1 |
| 1 | 33 uH | L1 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 680 uF | C1 | |
| 1 | 220 uF | C2 | |
| 1 | 10 nF C0G | C_0603_1608Metric | C3 |
| 2 | 1000 uF | C5, C6 | |
| 1 | 100k (active) | R_0603_1608Metric | R1 |
| 1 | 100k (dummy) | R_0603_1608Metric | R2 |
| 1 | 100 | R_0603_1608Metric | R3 |
| 1 | 100k | R_0603_1608Metric | R4 |
| 1 | 100k 0.1% (ref) | R_0603_1608Metric | R5 |
| 1 | 100k 0.1% (fb) | R_0603_1608Metric | R6 |
| 2 | 4.7k | R_0603_1608Metric | R7, R8 |
| 1 | 10k TEC_EN pull-down | R_0603_1608Metric | R9 |
| 1 | 10k 1% NTC divider | R_0603_1608Metric | R10 |
| 1 | 10k fan-tach pull-up | R_0603_1608Metric | R11 |
FrostChain-ESkin-Crate design files
The KiCad project lives in the shubhamFoT/FrostChain-ESkin-Crate repository on GitHub; these links point at the commit this page was built from.
FrostChain-ESkin-Crate: common questions
What microcontroller does the FrostChain-ESkin-Crate use?
The FrostChain-ESkin-Crate is built around the ESP32-S3, from the ESP32 family.
How many components are on the FrostChain-ESkin-Crate?
36 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the FrostChain-ESkin-Crate design files?
From the shubhamFoT/FrostChain-ESkin-Crate repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the FrostChain-ESkin-Crate design in my own project?
Yes, under the terms of its MIT license, which shubhamFoT chose for the repository.
Can I test firmware for the FrostChain-ESkin-Crate without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k