DroneController

Shubhkr08·DroneController·Drone Controller/PCB/DroneController.kicad_pcb

DroneController PCB layout, top view — open source STM32 board by Shubhkr08

About the DroneController PCB

DroneController is an open source STM32 PCB design by Shubhkr08, published on GitHub. It is a 2-layer board measuring 59.8 × 39.6 mm, with 43 components from 25 distinct parts.

Its main chip is the STM32F401CBUx, from the STM32 family. Other key parts include the AMS1117-3.3, MPU-6050, BMP280 and L7805. By type, the board carries 18 capacitors, 10 connectors, 5 ICs, 4 resistors, 3 diodes and 2 switches.

It belongs with the sensors designs in this gallery.

From the project

- STM32f4 cortex M4 based on board microcontroller for precision and fligt data simulation - MPU9250.(IMU) for statbility and orientation of board/vehicle. - BMP280 .(Barometer) barometer for altitude calculations . helps to hover the flight.

- STM32f4 cortex M4 based on board microcontroller for precision and fligt data simulation - MPU9250.(IMU) for statbility and orientation of board/vehicle. - BMP280 .(Barometer) barometer for altitude calculations . helps to hover the flight.

- ## Bill of Materials (BOM) | Serial Num | Description | Total (USD) | |----:|--------------------------|-------------| | 1 | PCB and Assembly |69.46 | | 2 | Shipping JLCPCB |19.51 |

DroneController, from the project README
From the project README

Main components on the DroneController

DroneController bill of materials (BOM)

43 components, 25 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AMS1117-3.3
U1
1
MPU-6050
U2
1
BMP280
U3
1
STM32F401CBUx
U4
1
L7805
U5
1
Crystal_GND23_Small
Y1
1
USB_B_Mini
J1
5
Conn_01x03_Male
J2, J3, J4, J5, J8
1
Conn_01x04_Pin
J6
1
Conn_01x02_Male
J7
1
Conn_01x03_Male
J9
1
Conn_01x04_Pin
J10
1
SW_Push
SW1
1
SW_SPDT
SW3
1
GREEN
D1
1
blue
D2
1
RED
D3
2
10uf
C1, C15
4
0.1uf
C2, C4, C5, C16
1
10nf
C3
Show 5 more
QtyPartRefs
2
100nf
C6, C8
1
2.2nf
C7
2
12pf
C9, C10
6
100pf
C11, C12, C13, C14, C17, C18
4
1k
R1, R2, R3, R5

DroneController design files

The KiCad project lives in the Shubhkr08/DroneController repository on GitHub; these links point at the commit this page was built from.

DroneController: common questions

What microcontroller does the DroneController use?

The DroneController is built around the STM32F401CBUx, from the STM32 family.

How big is the DroneController PCB?

The DroneController measures 59.8 × 39.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the DroneController?

43 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the DroneController design files?

From the Shubhkr08/DroneController repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the DroneController design in my own project?

The repository has no license, so all rights stay with Shubhkr08. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the DroneController without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards