Amp distortion
Skelebot·amp-distortion·board/amp.kicad_pcb
About the Amp distortion PCB
Amp distortion is an open source PCB design by Skelebot, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 29.8 × 54.6 mm, with 23 components from 20 distinct parts.
Other key parts include the TL071. By type, the board carries 8 resistors, 5 capacitors, 3 connectors, 3 diodes, 1 IC and 1 switch.
It belongs with the audio designs in this gallery.
From the project
Open-source amp + germanium diode distortion pedal
- No distortion: Do not install D2, D3 and SW1. Replace RV2 with a standard 10k resistor across its outer terminals - Log pot instead of reverse-log: Note that the middle pad of RV1 is not traced, so you can connect a standard logarithmic potentiometer backwards. Please note that when using a non-reverse-log potentiometer backwards, gain control will be reversed - the knob will have to be turned counter-clockwise to increase gain. - On/Off LED: The pedal does not have an on/off LED, which allows it to have true bypass with a 2PDT switch instead of a more expensive 3PDT switch. If you have a…
Main components on the Amp distortion
Amp distortion bill of materials (BOM)
23 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TL071 | SO-8_5.3x6.2mm_P1.27mm | U1 |
| 1 | GUITAR_IN | Jack_6.35mm_Neutrik_NRJ6HM-1-AU_Horizontal | J1 |
| 1 | POWER | BarrelJack_Horizontal | J2 |
| 1 | OUT | Jack_6.35mm_Neutrik_NRJ6HM-1-AU_Horizontal | J3 |
| 1 | 500K | PinSocket_1x03_P2.54mm_Vertical | RV1 |
| 1 | 10K | PinSocket_1x03_P2.54mm_Vertical | RV2 |
| 1 | SW_DIST | PinSocket_1x02_P2.54mm_Vertical | SW2 |
| 1 | D_Schottky | D_DO-15_P12.70mm_Horizontal | D1 |
| 2 | AAZ15 | D_DO-35_SOD27_P12.70mm_Horizontal | D3, D4 |
| 1 | 1uF | C_0603_1608Metric | C1 |
| 1 | 100nF | C_0603_1608Metric | C2 |
| 2 | 47pF | C_0603_1608Metric | C3, C4 |
| 1 | 10uF | C_0603_1608Metric | C5 |
| 1 | 22M | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R1 |
| 2 | 100K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3, R4 |
| 1 | 10M | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
| 1 | 2.7K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R6 |
| 1 | 1K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R7 |
| 1 | 150K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R8 |
| 1 | 470 | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R9 |
Amp distortion design files
The KiCad project lives in the Skelebot/amp-distortion repository on GitHub; these links point at the commit this page was built from.
- Layoutboard/amp.kicad_pcb
- BOMboard/bom.csv
Amp distortion: common questions
How big is the Amp distortion PCB?
The Amp distortion measures 29.8 × 54.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Amp distortion?
23 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Amp distortion design files?
From the Skelebot/amp-distortion repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Amp distortion design in my own project?
Yes, under the terms of its GPL-3.0 license, which Skelebot chose for the repository.
Similar boards
KLOR
GEIGEIGEIST
160.2 × 118.3 mm79 parts2LGPL-3.01.2kButtonsLEDs
shanteacontrols
390 × 37 mm82 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956Pots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956PicoGUS Hand386
polpo
29.2 × 75.2 mm43 parts4LGPL-2.0800Snark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687