V1
About the V1 PCB
V1 is an open source STM32 PCB design by Sleeeee, published on GitHub under the MIT license. It is a 2-layer board measuring 56 × 43 mm, with 65 components from 34 distinct parts.
Its main chip is the STM32F103C8Tx, from the STM32 family. Other key parts include the AMS1117-3.3, M24C02-WMN, ATtiny85-20P and AP2112K-3.3. By type, the board carries 23 resistors, 16 capacitors, 9 connectors, 5 ICs, 3 test points and 3 diodes.
From the project
Damn Vulnerable Hardware (DVH)
Main components on the V1
V1 bill of materials (BOM)
65 components, 34 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103C8Tx | LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | M24C02-WMN | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | ATtiny85-20P | DIP-8_W7.62mm | U4 |
| 1 | AP2112K-3.3 | SOT-23-5 | U5 |
| 2 | 2N7002 | SOT-23 | Q1, Q2 |
| 1 | 16MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB_B_Micro | USB_Micro-B_Amphenol_10118194-0001LF_Horizontal | J1 |
| 1 | SEL_IN | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | SEL_VDD | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | SWD_INT | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | UART_INT | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | I2C_INT | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | RFID_INT | PinHeader_1x08_P2.54mm_Vertical | J7 |
| 1 | GLITCH_IN | PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | GLITCH_EN | PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | SW_BOOT0 | SW_SPDT_CK_JS102011SAQN | SW1 |
| 1 | LAB_RST | SW_Push_1TS009xxxx-xxxx-xxxx_6x6x5mm | SW2 |
| 1 | DOOR | TestPoint_THTPad_D2.0mm_Drill1.0mm | TP1 |
| 1 | WP | TestPoint_THTPad_D2.0mm_Drill1.0mm | TP2 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | GLITCH_TRIG | TestPoint_THTPad_D2.0mm_Drill1.0mm | TP3 |
| 2 | RED | LED_0603_1608Metric | D1, D3 |
| 1 | GREEN | LED_0603_1608Metric | D2 |
| 1 | 120R | L_0603_1608Metric | FB1 |
| 2 | 22u | C_0805_2012Metric | C1, C2 |
| 2 | 10p | C_0402_1005Metric | C3, C4 |
| 1 | 10u | C_0603_1608Metric | C5 |
| 6 | 100n | C_0402_1005Metric | C6, C7, C8, C9, C13, C16 |
| 2 | 1u | C_0402_1005Metric | C10, C11 |
| 1 | 10n | C_0402_1005Metric | C12 |
| 2 | 1u | C_0805_2012Metric | C14, C15 |
| 11 | 1k5 | R_0402_1005Metric | R1, R3, R9, R12, R13, R15, R19, R20 +3 |
| 11 | 10k | R_0402_1005Metric | R2, R4, R5, R6, R7, R8, R10, R11 +3 |
| 1 | 47 | R_1206_3216Metric | R17 |
V1 design files
The KiCad project lives in the Sleeeee/dvh repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/v1/kicad/v1.kicad_pcb
- Schematichardware/v1/kicad/v1.kicad_sch
V1: common questions
What microcontroller does the V1 use?
The V1 is built around the STM32F103C8Tx, from the STM32 family.
How big is the V1 PCB?
The V1 measures 56 × 43 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the V1?
65 components, from 34 distinct parts. The full bill of materials is listed on this page.
Where can I download the V1 design files?
From the Sleeeee/dvh repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the V1 design in my own project?
Yes, under the terms of its MIT license, which Sleeeee chose for the repository.
Can I test firmware for the V1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in dvh
Similar boards
STM32LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7k
STM32Type c
google
188 × 30 mm17 parts2LApache-2.02.9k
STM32Main panel
234 × 84 mm26 parts4LApache-2.02.9k
STM32Base
52.3 × 52.3 mm36 parts2LApache-2.02.9k
STM32Type a
150 × 30 mm14 parts2LApache-2.02.9k
STM32Type e
140.5 × 30 mm13 parts2LApache-2.02.9k