23 open source boards using the M24C02-WMN
Real designs built with the M24C02-WMN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Zoxnoxious Z5524 (SSI2130/AS3394)
brer-rabbit
80 × 80 mm222 parts4LGPL-3.068STM32
STM32F103RB USB to UART SPI I2C
Stulinaz
80 × 80 mm67 parts2LNo license23AVR/Arduino
Hw openmower yardforce
xtech
180 × 170 mm275 parts4LCC-BY-4.012Hw openmower sabo
xtech
254 × 115 mm322 parts6LCC-BY-NC-4.05ESP32
Smart uppatvind
moucha19
74 × 36 mm66 parts4LCERN-OHL-W-2.05FPGA
Pcb
vgacentrifuge
177.7 × 96.7 mm398 parts6LNo license1RP2040/RP2350
Prototype test
DIaLOGIKa-GmbH
103.9 × 119.3 mm53 parts2LMIT1STM32
KASM ACTUATOR PCB REV2
gabeak2
121 × 70.6 mm247 parts6LGPL-3.00AVR/Arduino
Pillex main
xPiTi
234 × 117 mm209 parts2LNo license0QCB board
bartkepl
101.6 × 128.7 mm171 parts4LMIT0RP2040/RP2350
Tc2-main
TheCacophonyProject
73 × 75.5 mm161 parts6LCERN-OHL-W-2.00RP2040/RP2350
Spool
TheCacophonyProject
80 × 99 mm133 parts4LCERN-OHL-W-2.00STM32
V1
Sleeeee
56 × 43 mm65 parts2LMIT0STM32
Keyboard addon
aramcon-badge
65 × 63.5 mm23 parts2LNo license0PIC
FlappyBird PIC18F4550
Thomas-GAUTRON
76.2 × 63.5 mm14 parts2LNo license0RP2040/RP2350
Nerf target v1
DIaLOGIKa-GmbH
103.9 × 119.3 mm51 parts2LMIT1STM32
Dvh
Sleeeee
49 × 37 mm36 parts2LMIT0Z3340 VCO
brer-rabbit
80 × 80 mm139 parts4LGPL-3.068RP2040/RP2350
Nerf target v1 panel
DIaLOGIKa-GmbH
223.9 × 240.4 mm51 parts2LMIT1Z3372 Filter
brer-rabbit
80 × 80 mm120 parts4LGPL-3.068Raspberry Pi
Zoxnoxious Backplane and VCA
brer-rabbit
133.8 × 102.9 mm86 parts4LGPL-3.068Zoxnoxious 2203 FM Operator Type-N (OPN)
brer-rabbit
80 × 80 mm34 parts4LGPL-3.068Zoxnoxiouscard
brer-rabbit
80 × 80 mm16 parts4LGPL-3.068
How designs wire the M24C02-WMN
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the M24C02-WMN connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 11 of 15 designs, most often 10 kΩ (then 4.7 kΩ).
- The SCL pin has a pull-up to 3.3V on 11 of 15 designs, most often 10 kΩ (then 4.7 kΩ).
- The VCC pin has a decoupling capacitor on 11 of 15 designs, most often 100 nF (then 4.7 µF).
- The E2 pin is tied to GND on 9 of 15 designs (not connected on 3, a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| E2pin 3 | Connected to: GND 60% · not connected 20% | — |
| VSSpin 4 | Connected to: GND 93% | — |
| SDApin 5 | Connected to: The microcontroller 53%, a connector 47% |
|
| SCLpin 6 | Connected to: The microcontroller 53%, a connector 47% |
|
| WCpin 7 | Connected to: A connector 27% · GND 27% |
|
| VCCpin 8 | Connected to: 3.3V 93% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Zoxnoxious Backplane and VCA by brer-rabbit, STM32F103RB USB to UART SPI I2C by Stulinaz, Hw openmower yardforce by xtech and Smart uppatvind by moucha19.
The M24C02-WMN in open source designs
The gallery holds 23 open source boards using the M24C02-WMN from 15 GitHub repositories; a typical one measures about 80 × 80 mm and carries around 86 components.
61% use four copper layers or more, and 74% carry an open source license.
The most starred is Zoxnoxious Z5524 (SSI2130/AS3394) by brer-rabbit.
Parts used alongside the M24C02-WMN
Microcontrollers on boards using the M24C02-WMN
What boards using the M24C02-WMN are built for
M24C02-WMN: common questions
Where can I find a M24C02-WMN reference design?
Each of the 23 boards on this page is a real design using the M24C02-WMN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the M24C02-WMN SDA pin?
The SDA pin has a pull-up to 3.3V on 11 of 15 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 15 open source designs using the M24C02-WMN.
What pull-up resistor is used on the M24C02-WMN SCL pin?
The SCL pin has a pull-up to 3.3V on 11 of 15 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 15 open source designs using the M24C02-WMN.
What decoupling capacitors do designs use on the M24C02-WMN VCC pin?
The VCC pin has a decoupling capacitor on 11 of 15 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 15 open source designs using the M24C02-WMN.
What parts are used alongside the M24C02-WMN?
The RP2040, TPS5430DDA, W25Q128JVS, 2.54mm 1x5 socket and 2.54mm 1x6 socket appear in the most repositories here.
Which microcontrollers do boards using the M24C02-WMN use?
Most are built on RP2040/RP2350 (5), STM32 (5), AVR/Arduino (2) and Raspberry Pi (1).
How big is a typical board using the M24C02-WMN?
The median is 80 × 80 mm, and 39% are two-layer designs.
What is the most popular open source board using the M24C02-WMN?
By GitHub stars, Zoxnoxious Z5524 (SSI2130/AS3394) by brer-rabbit, with 68 stars.
Can I simulate one of these boards using the M24C02-WMN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.