HardLabs

Hall effect sensor easyC

SolderedElectronics·Hall-effect-sensor-breakout-with-analog-output---qwiic-hardware-design·CAD/V1.0.0/Hall_effect_sensor_easyC.kicad_pcb

Hall effect sensor easyC PCB layout, top view — open source AVR/Arduino board by SolderedElectronics
Simulate this board

About the Hall effect sensor easyC PCB

Hall effect sensor easyC is an open source AVR/Arduino PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 22 × 22 mm, with 12 components from 8 distinct parts.

Its main chip is the ATTINY404-SSNR, from the AVR/Arduino family. Other key parts include the SI7201-B-06-IV. By type, the board carries 4 relays, 2 ICs, 2 capacitors and 2 resistors.

It belongs with the sensors and dev boards & breakouts designs in this gallery.

From the project

Hardware design, BOM, gerbers and 3D files for Hall-effect-sensor-breakout-with-analog-output-&-qwiic designed by Soldered Electronics.

The Hall effect sensor breakout with analog output is a versatile and reliable sensor module designed to detect and measure magnetic fields. It utilizes the Hall effect principle, where the presence of a magnetic field induces a voltage proportional to the strength and direction of the field.

This sensor module features an analog output, which provides a continuous voltage signal that varies in response to changes in the magnetic field. The analog output allows for precise and real-time monitoring of magnetic field strength. It is commonly used in applications such as position sensing…

Hall effect sensor easyC, from the project README
From the project README

Main components on the Hall effect sensor easyC

SI7201-B-06-IVATTINY404-SSNR

Hall effect sensor easyC bill of materials (BOM)

12 components, 8 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
SI7201-B-06-IV
U1
1
ATTINY404-SSNR
U2
2
HOLE_3.2mm
H1, H2
2
easyC-SMD
K1, K3
1
HEADER-UPDI
K2
1
DSHP03TS-S
K4
2
0.1uF
C1, C2
2
10k
R1, R2

Hall effect sensor easyC design files

The KiCad project lives in the SolderedElectronics/Hall-effect-sensor-breakout-with-analog-output---qwiic-hardware-design repository on GitHub; these links point at the commit this page was built from.

Hall effect sensor easyC: common questions

What microcontroller does the Hall effect sensor easyC use?

The Hall effect sensor easyC is built around the ATTINY404-SSNR, from the AVR/Arduino family.

How big is the Hall effect sensor easyC PCB?

The Hall effect sensor easyC measures 22 × 22 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Hall effect sensor easyC?

12 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Hall effect sensor easyC design files?

From the SolderedElectronics/Hall-effect-sensor-breakout-with-analog-output---qwiic-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Hall effect sensor easyC design in my own project?

Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.

Can I test firmware for the Hall effect sensor easyC without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in Hall-effect-sensor-breakout-with-analog-output---qwiic-hardware-design

Similar boards