Pir na easyC breakout
SolderedElectronics·PIR-movement-sensor-board-qwiic-hardware-design·CAD/V1.0.0/Pir na easyC breakout.kicad_pcb
About the Pir na easyC breakout
Pir na easyC breakout is an open source AVR/Arduino PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 38 × 22 mm, with 12 components from 10 distinct parts.
Its main chip is the ATTINY404-SSNR, from the AVR/Arduino family. Other key parts include the AM312. By type, the board carries 4 relays, 2 ICs, 1 diode, 1 capacitor and 1 resistor.
It belongs with the sensors and dev boards & breakouts designs in this gallery.
From the project
Hardware design, BOM, gerbers and 3D files for PIR-movement-sensor-board-qwiic designed by Soldered Electronics.
A PIR (passive infrared) motion sensor is a device that detects physical movement within its field of vision by sensing changes in infrared radiation. This sensor works on the principle of detecting thermal thermal signals emitted by objects, mostly warm-blooded creatures like humans. The “passive” in the name refers to the fact that the sensor itself does not emit or radiate any energy for detection.

Main components on the Pir na easyC breakout
Pir na easyC breakout bill of materials (BOM)
12 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AM312 | PIR_senzor | U2 |
| 1 | ATTINY404-SSNR | SOIC-14 | U3 |
| 2 | HOLE_3.2MM HOLE_3.2mm | HOLE_3.2mm | H1, H2 |
| 1 | — | HOLE_L1 | |
| 2 | easyC-SMD | easyC-connector | K1, K3 |
| 1 | HEADER-UPDI | HEADER-UPDI | K2 |
| 1 | DSHP03TS-S | DSHP03TS-S | K4 |
| 1 | Purple | 0402LED | D1 |
| 1 | 100N 100n | 0603C | C3 |
| 1 | 2K2 2k2 | 0402R | R1 |
Pir na easyC breakout design files
The KiCad project lives in the SolderedElectronics/PIR-movement-sensor-board-qwiic-hardware-design repository on GitHub; these links point at the commit this page was built from.
Pir na easyC breakout: common questions
What microcontroller does the Pir na easyC breakout use?
The Pir na easyC breakout is built around the ATTINY404-SSNR, from the AVR/Arduino family.
How big is the Pir na easyC breakout?
The Pir na easyC breakout measures 38 × 22 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pir na easyC breakout?
12 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Pir na easyC breakout design files?
From the SolderedElectronics/PIR-movement-sensor-board-qwiic-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Pir na easyC breakout design in my own project?
Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.
Can I test firmware for the Pir na easyC breakout without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in PIR-movement-sensor-board-qwiic-hardware-design
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k