PenumaticBackpack
srikanth-444·PenumaticBackpack·Hardware/pneumatic Backpack v3.1/pneumatic Backpack v3.1.kicad_pcb
About the PenumaticBackpack PCB
PenumaticBackpack is an open source ESP32 PCB design by srikanth-444, published on GitHub. It is a 2-layer board measuring 64 × 73 mm, with 94 components from 15 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1-N8R2, from the ESP32 family. Other key parts include the INA332AIDGKR, MCZ33996EK and ltc2498iuhf. By type, the board carries 40 resistors, 32 diodes, 8 connectors, 6 capacitors, 4 ICs and 2 modules.
From the project
Pneumatic Backpack development(hardware and software build up from scratch)

Main components on the PenumaticBackpack
PenumaticBackpack bill of materials (BOM)
94 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC-1-N8R2 | XCVR_ESP32-S3-DEVKITC-1-N8R2 | U1 |
| 2 | INA332AIDGKR | SOP65P490X110-8N | U3, U4 |
| 1 | MCZ33996EK | SOP65P1030X265-33N | U5 |
| 2 | ltc2498iuhf LTC2498IUHF_TRPBF | QFN-38_UHF | A2, A3 |
| 2 | CONN_01X12_PIN Conn_02x08_Odd_Even | JST_PHD_S16B-PHDSS_2x08_P2.00mm_Horizontal | J1, J5 |
| 1 | CONN_01X01_PIN Conn_01x01_Pin | SolderWire-0.15sqmm_1x01_D0.5mm_OD1.5mm | J2 |
| 2 | CONN_02X16_TOP_BOTTOM Conn_02x16_Top_Bottom | PinHeader_2x16_P2.54mm_Vertical | J3, J4 |
| 3 | CONN_01X02_PIN Conn_01x02_Pin | PinSocket_1x02_P2.54mm_Vertical | J9, J10, J11 |
| 1 | Conn_01x04_Pin | PinSocket_1x04_P2.54mm_Vertical | Bus_D1 |
| 1 | Conn_01x04_Pin | PinSocket_1x04_P2.54mm_Horizontal | Bus_D2 |
| 16 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2, D3, D4, D5, D6, D7, D8 +8 |
| 16 | D | D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D17, D18, D19, D20, D21, D22, D23, D24 +8 |
| 4 | 10UF 10uf | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2, C3, C4 |
| 2 | 0.1UF 0.1uf | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C5, C6 |
| 40 | 100K 100k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21, R22, R23, R24, R25, R26, R27, R28 +32 |
PenumaticBackpack design files
The KiCad project lives in the srikanth-444/PenumaticBackpack repository on GitHub; these links point at the commit this page was built from.
PenumaticBackpack: common questions
What microcontroller does the PenumaticBackpack use?
The PenumaticBackpack is built around the ESP32-S3-DEVKITC-1-N8R2, from the ESP32 family.
How big is the PenumaticBackpack PCB?
The PenumaticBackpack measures 64 × 73 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PenumaticBackpack?
94 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the PenumaticBackpack design files?
From the srikanth-444/PenumaticBackpack repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the PenumaticBackpack design in my own project?
The repository has no license, so all rights stay with srikanth-444. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PenumaticBackpack without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Earlier revisions in the repo: pneumatic Backpack v3.0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k