WeatherStation
steand·WeatherStation·doc/kicad/WeatherStation.kicad_pcb
About the WeatherStation PCB
WeatherStation is an open source ESP32 PCB design by steand, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 88.9 × 68.6 mm, with 23 components from 17 distinct parts.
Its main chip is the ESP-WROOM-32, from the ESP32 family. Other key parts include the Rain_Sensor, Mod_Spannungsteiler, Mod_Dual_Schmitt_Triger and Mod_Regulator_3.0V. By type, the board carries 7 connectors, 5 ICs, 4 capacitors, 4 resistors, 2 switches and 1 transistor.
It belongs with the iot & wireless and power & battery designs in this gallery.
From the project
Eigenbau Wetterstation/DIY Weather Station
Version 0.1 (under construction, not stabil)
In diesem Projekt habe ich mir eine kleine Wetterstation gebaut. Meine Motivation war, dass es eigentlich nichts erschwingliches gibt was in die offenen Smart-Home (bei mir openHAB2) integrierbar ist.
Leistungsmerkmale: - Windgeschwindigkeit - Windrichtung - Regenmenge - Regensensor - Temperatur - Luftdruck - Luftfeuchtigkeit - Helligkeit
Main components on the WeatherStation
WeatherStation bill of materials (BOM)
23 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Rain_Sensor | Rain_Sensor | U4 |
| 1 | ESP-WROOM-32 | ESP32_Dev_Board | U6 |
| 1 | Mod_Spannungsteiler | Mod_SOT23_TO_10DIL | U7 |
| 1 | Mod_Dual_Schmitt_Triger | Mod_TSOP6_TO_8DIL | U8 |
| 1 | Mod_Regulator_3.0V | Mod_SOT23_TO_10DIL | U9 |
| 1 | IRLML2244 | SOT-23 | Q1 |
| 2 | Screw_Terminal_01x04 | TerminalBlock_bornier-4_P5.08mm | J8, J10 |
| 3 | Screw_Terminal_01x02 | TerminalBlock_bornier-2_P5.08mm | J9, J11, J15 |
| 1 | Conn_01x02_Male | Pin_Header_Straight_1x02_Pitch2.54mm | J16 |
| 1 | Prog | Socket_Strip_Straight_1x06_Pitch2.54mm | J19 |
| 1 | Reset | SW_PUSH_6mm | SW1 |
| 1 | Mode | SW_PUSH_6mm | SW2 |
| 1 | 1µF | CP_Radial_D4.0mm_P1.50mm | C2 |
| 2 | 10µ | CP_Radial_D4.0mm_P1.50mm | C3, C7 |
| 1 | 1µ | CP_Radial_D4.0mm_P1.50mm | C5 |
| 2 | 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P5.08mm_Vertical | R1, R2 |
| 2 | 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P5.08mm_Vertical | R3, R6 |
WeatherStation design files
The KiCad project lives in the steand/WeatherStation repository on GitHub; these links point at the commit this page was built from.
WeatherStation: common questions
What microcontroller does the WeatherStation use?
The WeatherStation is built around the ESP-WROOM-32, from the ESP32 family.
How big is the WeatherStation PCB?
The WeatherStation measures 88.9 × 68.6 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the WeatherStation?
23 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the WeatherStation design files?
From the steand/WeatherStation repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the WeatherStation design in my own project?
Yes, under the terms of its GPL-3.0 license, which steand chose for the repository.
Can I test firmware for the WeatherStation without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in WeatherStation
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k