61 open source boards using the ESP-WROOM-32

Real designs built with the ESP-WROOM-32, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

61 boardsClear filters|Most starred

How designs wire the ESP-WROOM-32

Read from the KiCad layouts of 34 open source designs, one per repository: what each pin of the ESP-WROOM-32 connects to, and the resistors, capacitors and other passives placed on it.

  • The 3V3 pin is tied to 3.3V on 30 of 34 designs (a signal on 3).
  • The EN pin has a pull-up to 3.3V on 25 of 34 designs, most often 10 kΩ (then 1 kΩ).
  • The SHD/SD2 pin is left unconnected on 27 of 33 designs (a signal on 6).
  • The SWP/SD3 pin is left unconnected on 27 of 33 designs (a signal on 6).
GNDpin 1, 15, 38Connected to: GND 94%
3V3pin 2Connected to: 3.3V 88%
ENpin 3Connected to: A connector 53%
  • Pull-up to 3.3V on 74% · 10 kΩ (15), 1 kΩ (6), 470 kΩ (2)
  • Capacitor to GND on 47% · 100 nF (9), 1 nF (4), 1 µF (3)
  • Series resistor on 35% · 470 Ω (4), 549 Ω (1), 330 Ω (1)
IO14pin 13Connected to: A connector 47% · not connected 21%
  • Series resistor on 35% · 10 Ω (7), 0 Ω (1), 27 Ω (1)
SHD/SD2pin 17Connected to: Not connected 82% · a signal 18%
SWP/SD3pin 18Connected to: Not connected 82% · a signal 18%
SCS/CMDpin 19Connected to: Not connected 82% · a signal 15%
SCK/CLKpin 20Connected to: Not connected 82% · a signal 15%
SDO/SD0pin 21Connected to: Not connected 82% · a signal 18%
SDI/SD1pin 22Connected to: Not connected 82% · a signal 18%
IO0pin 25Connected to: A connector 53%
  • Pull-up to 3.3V on 50% · 10 kΩ (6), 15 kΩ (1), 4.7 kΩ (1)
  • Series resistor on 32% · 10 Ω (2), 470 Ω (2), 330 Ω (1)
NCpin 32Connected to: Not connected 94%
RXD0pin 34Connected to: A connector 76%
  • Series resistor on 41% · 220 Ω (5), 10 kΩ (4), 0 Ω (4)
THERMAL_PADpin 39Connected to: GND 91%

23 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESP32-adapter by pcbreflux, Ulx3s by emard, ESP32-PoE Rev C by OLIMEX and ESP32-PoE-ISO Rev B by OLIMEX.

The ESP-WROOM-32 in open source designs

The gallery holds 61 open source boards using the ESP-WROOM-32 from 35 GitHub repositories; a typical one measures about 54 × 63 mm and carries around 81 components.

89% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.

The most starred is ESP32-li ion cell monitor pan by pcbreflux.

Microcontrollers on boards using the ESP-WROOM-32

ESP-WROOM-32: common questions

Where can I find a ESP-WROOM-32 reference design?

Each of the 61 boards on this page is a real design using the ESP-WROOM-32. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ESP-WROOM-32 3V3 pin connected?

The 3V3 pin is tied to 3.3V on 30 of 34 designs (a signal on 3). Counted from the KiCad layouts of 34 open source designs using the ESP-WROOM-32.

What pull-up resistor is used on the ESP-WROOM-32 EN pin?

The EN pin has a pull-up to 3.3V on 25 of 34 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 34 open source designs using the ESP-WROOM-32.

How is the ESP-WROOM-32 SHD/SD2 pin connected?

The SHD/SD2 pin is left unconnected on 27 of 33 designs (a signal on 6). Counted from the KiCad layouts of 34 open source designs using the ESP-WROOM-32.

What parts are used alongside the ESP-WROOM-32?

The CH340T(SSOP20W), SY8089AAAC(SOT23-5), BL4054B-42TPRN(SOT23-5), LAN8710A-EZC(QFN32) and Si3402-B-GM(QFN-20_5x5mm) appear in the most repositories here.

Which microcontrollers do boards using the ESP-WROOM-32 use?

Most are built on ESP32 (61).

How big is a typical board using the ESP-WROOM-32?

The median is 54 × 63 mm, and 89% are two-layer designs.

What is the most popular open source board using the ESP-WROOM-32?

By GitHub stars, ESP32-li ion cell monitor pan by pcbreflux, with 608 stars.

Can I simulate one of these boards using the ESP-WROOM-32 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part