SBBMicro
stefphd·SBBMicro·hardware/SBBMicro.kicad_pcb
About the SBBMicro PCB
SBBMicro is an open source NXP PCB design by stefphd, published on GitHub. It is a 2-layer board measuring 110 × 72 mm, with 30 components from 28 distinct parts.
Its main chip is the Teensy4.1, from the NXP family. Other key parts include the Mecostrain2038, Teensy4.0, ISM330DHCX, LIS3MDL and MCP4922-AK. By type, the board carries 13 connectors, 11 ICs, 1 switch, 1 diode, 1 capacitor and 1 resistor.
From the project
Source code for the self-balancing-bike microcontroller unit
This repository contains the source code for the self-balancing-bike micro-controller unit (Teensy 4.1-based 🚀️). The introduction shows the files and folders contained in this repository and how they are organized, the prerequisites necessary, and the procedures to be used in order to build and upload the code, to generate the documentation, and to automatically generate the control-algorithm code from the Simulink model (using matlab tools).
Main components on the SBBMicro
SBBMicro bill of materials (BOM)
30 components, 28 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Mecostrain2038 | Mecostrain-2038 | U1 |
| 1 | Teensy4.1 | Teensy41 | U2 |
| 1 | Teensy4.0 | Teensy40 | U3 |
| 1 | ISM330DHCX | ISM330DHCX | U4 |
| 1 | LIS3MDL | LIS3MDL | U5 |
| 1 | MCP4922-AK | MCP4922-AK | U6 |
| 1 | UltimateGPS | Ultimate-GPS | U7 |
| 1 | ArcherM+ | JST_1x04_P2.54 | U8 |
| 1 | Relay | Relay | U9 |
| 1 | ESCON_module-50/5 | Escon module-50-5 | U10 |
| 1 | A4988 | A4988 | U11 |
| 2 | Brake mtr JST | JST_1x04_P2.54 | J1, J12 |
| 1 | Aux analog JST | JST_1x04_P2.54 | J2 |
| 1 | Steer mtr JST | JST_1x06_P2.54 | J3 |
| 2 | Power JST | JST_1x04_P2.54 | J4, J10 |
| 1 | On/off JST | JST_1x03_P2.54 | J5 |
| 1 | Throttle JST | JST_1x02_P2.54 | J6 |
| 1 | Encoder JST | JST_1x05_P2.54 | J7 |
| 1 | Steer trq & ang JST | JST_1x06_P2.54 | J8 |
| 1 | Bat in | TerminalBlock_bornier-2_P5.08mm | J9 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Brake mtr out | JST_1x04_P2.54 | J15 |
| 1 | Power mtr out | TerminalBlock_bornier-2_P5.08mm | J16 |
| 1 | ON/OFF | SW_PUSH_6mm | SW1 |
| 1 | Voltage_regulator_5V | Voltage-reg_5V | VR0 |
| 1 | Voltage_regulator_12V | Voltage-reg_12V | VR1 |
| 1 | D | D_DO-34_SOD68_P7.62mm_Horizontal | D1 |
| 1 | 100uC | CP_Radial_D5.0mm_P2.50mm | C1 |
| 1 | R220 | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1 |
SBBMicro design files
The KiCad project lives in the stefphd/SBBMicro repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/SBBMicro.kicad_pcb
- Schematichardware/SBBMicro.kicad_sch
SBBMicro: common questions
What microcontroller does the SBBMicro use?
The SBBMicro is built around the Teensy4.1, from the NXP family.
How big is the SBBMicro PCB?
The SBBMicro measures 110 × 72 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SBBMicro?
30 components, from 28 distinct parts. The full bill of materials is listed on this page.
Where can I download the SBBMicro design files?
From the stefphd/SBBMicro repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the SBBMicro design in my own project?
The repository has no license, so all rights stay with stefphd. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the SBBMicro without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
Similar boards
NXP
32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763NXP
MCL6809
MicroCoreLabs
32.3 × 61 mm7 parts4LNo license532NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532NXP
MCL65+
MicroCoreLabs
72.6 × 64.1 mm6 parts2LNo license532NXP
MCLZ8
MicroCoreLabs
37.1 × 61.5 mm6 parts4LNo license532