Basys3 to lb
SteveLRojas·pmod_modules·basys3_to_lb/HW/basys3_to_lb.kicad_pcb
About the Basys3 to lb PCB
Basys3 to lb is an open source WCH CH32/CH55x PCB design by SteveLRojas, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 47.2 × 69.1 mm, with 35 components from 18 distinct parts.
Its main chip is the CH552G, from the WCH CH32/CH55x family. Other key parts include the MT9700. By type, the board carries 13 connectors, 6 capacitors, 6 resistors, 4 test points, 2 ICs and 1 switch.
From the project
Place to keep all my PMOD modules
Main components on the Basys3 to lb
Basys3 to lb bill of materials (BOM)
35 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MT9700 | SOT-23-5 | U1 |
| 1 | CH552G | SO-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | Conn_02x22_Odd_Even | PinHeader_2x22_P2.54mm_Vertical | J2 |
| 2 | Conn_01x02 | PinHeader_1x02_P1.27mm_Vertical | J3, J10 |
| 1 | Conn_02x05_Odd_Even | PinHeader_2x05_P2.54mm_Vertical | J4 |
| 4 | Conn_01x03 | PinHeader_1x03_P1.27mm_Vertical | J5, J6, J7, J9 |
| 1 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J8 |
| 3 | Conn_02x02_Odd_Even | PinHeader_2x02_P2.54mm_Vertical | J11, J12, J13 |
| 2 | PMOD-Device-x2-Type-1A-GPIO | pmod_6x2_pin_mirrored | PMOD1, PMOD2 |
| 1 | SW_Push | SW_SPST_PTS810 | SW1 |
| 4 | TestPoint | TestPoint_Loop_D2.50mm_Drill1.0mm | TP1, TP2, TP3, TP4 |
| 1 | orange | LED_0805_2012Metric | D1 |
| 6 | 0.1u | C_0805_2012Metric | C1, C2, C3, C4, C5, C6 |
| 2 | 5K1 | R_0805_2012Metric | R1, R2 |
| 1 | 4.7k | R_0805_2012Metric | R3 |
| 2 | 10k | R_0805_2012Metric | R4, R6 |
| 1 | 470 | R_0805_2012Metric | R5 |
Basys3 to lb design files
The KiCad project lives in the SteveLRojas/pmod_modules repository on GitHub; these links point at the commit this page was built from.
Basys3 to lb: common questions
What microcontroller does the Basys3 to lb use?
The Basys3 to lb is built around the CH552G, from the WCH CH32/CH55x family.
How big is the Basys3 to lb PCB?
The Basys3 to lb measures 47.2 × 69.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Basys3 to lb?
35 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Basys3 to lb design files?
From the SteveLRojas/pmod_modules repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Basys3 to lb design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which SteveLRojas chose for the repository.
Can I test firmware for the Basys3 to lb without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.
More boards in pmod_modules
Pmod audio mono
SteveLRojas
44.3 × 18.3 mm22 parts2LCERN-OHL-P-2.00PMOD HDMI
SteveLRojas
54.1 × 22.9 mm16 parts2LCERN-OHL-P-2.00Pmod level shifter 8p
SteveLRojas
46.5 × 18.5 mm14 parts2LCERN-OHL-P-2.00Pmod sd card
SteveLRojas
32.1 × 20 mm10 parts2LCERN-OHL-P-2.00Pmod level shifter 4p
SteveLRojas
28.5 × 16.3 mm10 parts2LCERN-OHL-P-2.00Basys pmod converter
SteveLRojas
31.7 × 86.4 mm10 parts2LCERN-OHL-P-2.00Pmod usb serial
SteveLRojas
33.2 × 17 mm10 parts2LCERN-OHL-P-2.00Pmod mem 2v0
SteveLRojas
25 × 19 mm7 parts2LCERN-OHL-P-2.00PMOD MEM
SteveLRojas
22.9 × 20.3 mm6 parts2LCERN-OHL-P-2.00
Similar boards
WCH CH32/CH55x
Ps2usb
rasteri
40 × 55 mm25 parts2LNo license428WCH CH32/CH55x
CH32X-48
rgoulter
224.6 × 74.2 mm112 parts2LNo license230WCH CH32/CH55x
CH32X-60-ANSI-Improved
rgoulter
285 × 94.2 mm149 parts2LNo license230WCH CH32/CH55x
CH32X-75
rgoulter
285 × 94.2 mm318 parts2LNo license230WCH CH32/CH55x
CH552-48
rgoulter
224.6 × 74.2 mm107 parts2LNo license230WCH CH32/CH55x
Webusb programmer rev6
laneboysrc
38 × 20 mm18 parts2LMIT87