USB Knob
SteveLRojas·USB_Knob·HW/USB_Knob/V1.1/USB_Knob.kicad_pcb
About the USB Knob PCB
USB Knob is an open source WCH CH32/CH55x PCB design by SteveLRojas, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 55 × 85 mm, with 39 components from 17 distinct parts.
Its main chip is the CH552T, from the WCH CH32/CH55x family. Other key parts include the 74LVC1G17. By type, the board carries 16 resistors, 9 capacitors, 4 switches, 3 ICs, 3 connectors and 3 diodes.
From the project
A USB knob that can scroll, pan, adjust the volume, and more. Uses the CH552 USB microcontroller.
Main components on the USB Knob
USB Knob bill of materials (BOM)
39 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH552T | TSSOP-20_4.4x6.5mm_P0.65mm | U1 |
| 2 | 74LVC1G17 | SOT-353_SC-70-5 | U2, U3 |
| 1 | Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | Conn_01x03 | PinHeader_1x03_P2.54mm_Horizontal | J2 |
| 1 | Conn_01x02 | PinHeader_1x02_P2.54mm_Horizontal | J3 |
| 3 | LL3301NF065QG | LL3301NF065QG | S1, S2, S3 |
| 1 | RotaryEncoder_Switch | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW1 |
| 3 | ORANGE | LED_0805_2012Metric | D1, D2, D3 |
| 1 | 10u | C_1206_3216Metric | C1 |
| 4 | 0.1u | C_0805_2012Metric | C2, C3, C8, C9 |
| 2 | 20p | C_0805_2012Metric | C4, C5 |
| 2 | 0.01u | C_0805_2012Metric | C6, C7 |
| 2 | 5K1 | R_0805_2012Metric | R1, R2 |
| 9 | 1k | R_0805_2012Metric | R3, R4, R5, R6, R7, R8, R9, R10 +1 |
| 3 | 10k | R_0805_2012Metric | R12, R13, R14 |
| 2 | 0 | R_0805_2012Metric | R15, R16 |
USB Knob design files
The KiCad project lives in the SteveLRojas/USB_Knob repository on GitHub; these links point at the commit this page was built from.
USB Knob: common questions
What microcontroller does the USB Knob use?
The USB Knob is built around the CH552T, from the WCH CH32/CH55x family.
How big is the USB Knob PCB?
The USB Knob measures 55 × 85 mm, has 2 copper layers and is 4.69 mm thick.
How many components are on the USB Knob?
39 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the USB Knob design files?
From the SteveLRojas/USB_Knob repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the USB Knob design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which SteveLRojas chose for the repository.
Can I test firmware for the USB Knob without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.
Similar boards
WCH CH32/CH55x
Ps2usb
rasteri
40 × 55 mm25 parts2LNo license428WCH CH32/CH55x
CH32X-48
rgoulter
224.6 × 74.2 mm112 parts2LNo license230WCH CH32/CH55x
CH32X-60-ANSI-Improved
rgoulter
285 × 94.2 mm149 parts2LNo license230WCH CH32/CH55x
CH32X-75
rgoulter
285 × 94.2 mm318 parts2LNo license230WCH CH32/CH55x
CH552-48
rgoulter
224.6 × 74.2 mm107 parts2LNo license230WCH CH32/CH55x
Webusb programmer rev6
laneboysrc
38 × 20 mm18 parts2LMIT87