AirNode-Room-Sensor
Syren0914·AirNode-Room-Sensor
About the AirNode-Room-Sensor PCB
AirNode-Room-Sensor is an open source ESP32 PCB design by Syren0914, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 70 × 100 mm, with 15 components from 10 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI_TH, from the ESP32 family. By type, the board carries 4 switches, 1 IC, 1 buzzer, 1 jumper and 1 resistor.
It belongs with the sensors and iot & wireless designs in this gallery.
From the project
Open hardware ESP32-C3 indoor air-quality monitor with CO2, PM, VOC, temperature and humidity sensing
AirNode is an ESP32-C3 based indoor air-quality monitor in a compact 70 mm × 100 mm enclosure. It combines a round color display, four buttons, an audible alarm, and connections for environmental sensor modules.
- ESP32-C3 SuperMini with Wi-Fi and Bluetooth LE - 1.28-inch round SPI TFT - SHT40 temperature and humidity sensor - SCD40 carbon-dioxide sensor connection - SGP41 VOC and NOx sensor connection - SPS30 particulate-matter sensor connection - Back-mounted passive piezo buzzer on GPIO20 - Four buttons: Up, Down, Select, and Back - Two-layer 70 mm × 100 mm PCB with 8 mm corner radii -…

Main components on the AirNode-Room-Sensor
AirNode-Room-Sensor bill of materials (BOM)
15 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3_SUPERMINI_TH | MODULE_ESP32-C3_SUPERMINI_TH | U2 |
| 1 | Piezo Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | INSULATED WIRE | Wire_Link_P12.70mm | JP1 |
| 2 | 5.1k | R_0805_2012Metric | R_CC1, R_CC2 |
| 1 | SCD40 I2C | PinHeader_1x04_P2.54mm_Vertical | SCD40 |
| 2 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | SGP41, SPS30 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | SHT40 |
| 4 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4 |
| 1 | Conn_01x07 | PinHeader_1x07_P2.54mm_Vertical | TFT1 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
AirNode-Room-Sensor design files
The KiCad project lives in the Syren0914/AirNode-Room-Sensor repository on GitHub; these links point at the commit this page was built from.
- LayoutRoom Sensor.kicad_pcb
- SchematicRoom Sensor.kicad_sch
- BOMBOM.csv
AirNode-Room-Sensor: common questions
What microcontroller does the AirNode-Room-Sensor use?
The AirNode-Room-Sensor is built around the ESP32-C3_SUPERMINI_TH, from the ESP32 family.
How big is the AirNode-Room-Sensor PCB?
The AirNode-Room-Sensor measures 70 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the AirNode-Room-Sensor?
15 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the AirNode-Room-Sensor design files?
From the Syren0914/AirNode-Room-Sensor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the AirNode-Room-Sensor design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which Syren0914 chose for the repository.
Can I test firmware for the AirNode-Room-Sensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k