Fume ex
t2ofaced·Fume-ex·PCB/fume-ex.kicad_pcb
About the Fume ex PCB
Fume ex is an open source ESP8266 PCB design by t2ofaced, published on GitHub under the MIT license. It is a 2-layer board measuring 106.9 × 42.2 mm, with 49 components from 24 distinct parts.
Its main chip is the ESP-12E, from the ESP8266 family. Other key parts include the TPS563202S and AMS1117-3.3. By type, the board carries 17 capacitors, 12 resistors, 6 diodes, 5 connectors, 3 ICs and 2 switches.
From the project
Fume extractor
Fume-ex is a DIY fume extractor that i built for myself it pulls soldering fumes away from my desk space so i don't have to breathe them in, it runs on 12V DC and has two main parts, a custom PCB and a 12V fan. The PCB has an ESP-12E on it, so the plan is to control it from a phone as well, but not for now.
Fume-ex has 2 buttons on the board, UP and DOWN button as the name says, the UP button increases the speed of the fan and the DOWN button decreases the speed of the fan, the board also has 4 LEDs which change their color according to the speed of the fan.
Main components on the Fume ex
Fume ex bill of materials (BOM)
49 components, 24 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS563202S | SOT-563 | U1 |
| 1 | ESP-12E | ESP-12E | U2 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U4 |
| 1 | IRL520N | TO254P1054X469X1930-3 | Q1 |
| 1 | Barrel_Jack | BarrelJack_Horizontal | J1 |
| 1 | SCREW_TERMINAL_01X02 Screw_Terminal_01x02 | TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J2 |
| 1 | CONN_01X05_PIN Conn_01x05_Pin | PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | FAN1-PAD1 | SolderWirePad_1x01_SMD_2x4mm | J8 |
| 1 | FAN1-PAD2 | SolderWirePad_1x01_SMD_2x4mm | J9 |
| 1 | GPIO0 | SW_SPST_TS-1088-xR020 | GPIO0 |
| 1 | SW-SPEEDUP | SW_PUSH-12mm | SW1 |
| 1 | SW_SPEEDDOWN | SW_PUSH-12mm | SW2 |
| 1 | BC847 | SOT23 | T1 |
| 4 | LED_WS2812B | LED_WS2812B | D1, D2, D3, D4 |
| 2 | SS34 | D_SMA | D5, D6 |
| 1 | SRN6045TA-100M | IND_SRN6045TA-100M | L1 |
| 2 | 10UF 10uF | C_0805_2012Metric | C1, C2 |
| 6 | 0.1UF 0.1uF | C_0805_2012Metric | C3, C4, C7, C13, C15, C16 |
| 9 | 22UF 22uF | C_0805_2012Metric | C5, C6, C8, C9, C10, C11, C12, C14 +1 |
| 8 | 10K | R_0805_2012Metric | R1, R2, R4, R5, R6, R7, R9, R10 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 52K | R_0805_2012Metric | R3 |
| 1 | 100 | R_0805_2012Metric | R8 |
| 1 | 1K | R_0805_2012Metric | R11 |
| 1 | 470 | R_0805_2012Metric | R12 |
Fume ex design files
The KiCad project lives in the t2ofaced/Fume-ex repository on GitHub; these links point at the commit this page was built from.
Fume ex: common questions
What microcontroller does the Fume ex use?
The Fume ex is built around the ESP-12E, from the ESP8266 family.
How big is the Fume ex PCB?
The Fume ex measures 106.9 × 42.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Fume ex?
49 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Fume ex design files?
From the t2ofaced/Fume-ex repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Fume ex design in my own project?
Yes, under the terms of its MIT license, which t2ofaced chose for the repository.
Can I test firmware for the Fume ex without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
Similar boards
ESP8266
ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1kESP8266
HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738ESP8266
RatGDO-OpenSource-Bare-ESP8266
Kaldek
55 × 82.7 mm20 parts2LMIT506ESP8266
RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506ESP8266
Goatgdo
Kaldek
32.9 × 53.3 mm23 parts2LMIT506ESP8266
Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398