Rp2350 adapter

teaguecl·nes_tengen_rambo1_research·hardware/rp2350_adapter/rp2350_adapter.kicad_pcb

Rp2350 adapter PCB layout, top view — open source RP2040/RP2350 board by teaguecl

About the Rp2350 adapter PCB

Rp2350 adapter is an open source RP2040/RP2350 PCB design by teaguecl, published on GitHub under the MIT license. It is a 2-layer board measuring 75 × 96 mm, with 23 components from 12 distinct parts.

Its main chip is the AO3401A (P-ch), from the RP2040/RP2350 family. Other key parts include the Olimex RP2350-PICO2-BB48, 74HCT541 (e.g. SN74HCT541N) and 74LVC541A (e.g. 74LVC541AD). By type, the board carries 7 capacitors, 6 ICs, 5 resistors, 3 transistors, 1 connector and 1 diode.

It belongs with the retro computing designs in this gallery.

From the project

Reverse engineering of the Tengen RAMBO-1 (337006, iNES mapper 64): findings, emulator guide, FPGA notes, hardware-verified test ROMs, jig and adapter designs

KiCad projects for the boards used to characterise the RAMBO-1.

Each board folder has the KiCad project (.kicadpro, .kicadsch, .kicadpcb), its symbol library, the nescart.pretty footprints.

- The designs were built and used. The RP2350 adapter board was checked against the pin map (all 33 signals match) and is documented in ../docs/rp2350adapterplan.md and ../docs/rp2350bringup.md. - Loopback calibration of the adapter's edge timing has not been done (it needs jumper wires). Treat adapter timings of a few ns as uncertain. - The Olimex module is third-party…

Main components on the Rp2350 adapter

Olimex RP2350-PICO2-BB4874HCT541 (e.g. SN74HCT541N)74LVC541A (e.g. 74LVC541AD)

Rp2350 adapter bill of materials (BOM)

23 components, 12 distinct parts.

QtyPartRefs
1
Olimex RP2350-PICO2-BB48
U1
3
74HCT541 (e.g. SN74HCT541N)
U2, U3, U4
2
74LVC541A (e.g. 74LVC541AD)
U5, U6
1
AO3401A (P-ch)
Q1
2
2N7002 (N-ch)
Q2, Q3
1
On Shore 302-S401
J2
1
LED
D1
5
100nF
C1, C2, C3, C4, C5
2
10uF
C6, C7
2
10k
R1, R3
2
100k
R2, R4
1
1k
R5

Rp2350 adapter design files

The KiCad project lives in the teaguecl/nes_tengen_rambo1_research repository on GitHub; these links point at the commit this page was built from.

Rp2350 adapter: common questions

What microcontroller does the Rp2350 adapter use?

The Rp2350 adapter is built around the AO3401A (P-ch), from the RP2040/RP2350 family.

How big is the Rp2350 adapter PCB?

The Rp2350 adapter measures 75 × 96 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rp2350 adapter?

23 components, from 12 distinct parts. The full bill of materials is listed on this page.

Where can I download the Rp2350 adapter design files?

From the teaguecl/nes_tengen_rambo1_research repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Rp2350 adapter design in my own project?

Yes, under the terms of its MIT license, which teaguecl chose for the repository.

Can I test firmware for the Rp2350 adapter without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in nes_tengen_rambo1_research

Similar boards