SmartRele

techmiguel·smartRele

SmartRele PCB layout, top view — open source ESP8266 board by techmiguel

About the SmartRele PCB

SmartRele is an open source ESP8266 PCB design by techmiguel, published on GitHub under the CERN-OHL-W-2.0 license. It is a 2-layer board measuring 66.5 × 49 mm, with 32 components from 20 distinct parts.

Its main chip is the ESP-12F, from the ESP8266 family. Other key parts include the AMS1117-3.3. By type, the board carries 9 capacitors, 9 resistors, 3 diodes, 2 ICs, 2 connectors and 2 switches.

It belongs with the iot & wireless designs in this gallery.

From the project

Single-channel Wi-Fi relay module based on the ESP-12F (ESP8266) for 110–120 VAC and loads up to 10 A. Open hardware in KiCad 10, ready for full assembly at JLCPCB.

Single-channel Wi-Fi relay module based on the ESP-12F (ESP8266) for 110–120 VAC mains.

A 2-layer, 66.5 × 49 mm board that switches a mains load of up to 10 A from an ESP-12F. It is powered directly from the mains through an isolated HLK-PM01 supply and integrates input protection (time-lag fuse and varistor), a 16 A Omron G5RL power relay, status indicators and a programming header. All components sit on the top side, and the board is ready to be ordered fully assembled from JLCPCB (SMD and THT), with no hand soldering.

SmartRele, from the project README
From the project README

Main components on the SmartRele

SmartRele bill of materials (BOM)

32 components, 20 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AMS1117-3.3
U1
1
ESP-12F
U2
1
SS8050
Q1
1
C72334
N / L_OUT / L_IN
J1
1
C65114
PROG
J3
1
C2762401
T500mA 250V
F1
1
C113250
G5RL-1A-E-HR DC5
K1
1
HLK-PM01
PS1
1
07D221K
RV1
2
TS-1187A
SW1, SW2
1
1N4148W
D1
1
C2286
LED relay (red)
D2
1
C51933294
LED WiFi (blue)
D3
1
C112505
470uF 10V
C1
2
C45783
22uF 10V
C2, C4
5
100NF
100nF
C3, C5, C6, C7, C8
1
C19702
10uF
C9
6
10K
10k
R1, R2, R3, R4, R5, R7
2
1k
R6, R8
1
220
R9

SmartRele design files

The KiCad project lives in the techmiguel/smartRele repository on GitHub; these links point at the commit this page was built from.

SmartRele: common questions

What microcontroller does the SmartRele use?

The SmartRele is built around the ESP-12F, from the ESP8266 family.

How big is the SmartRele PCB?

The SmartRele measures 66.5 × 49 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the SmartRele?

32 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the SmartRele design files?

From the techmiguel/smartRele repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the SmartRele design in my own project?

Yes, under the terms of its CERN-OHL-W-2.0 license, which techmiguel chose for the repository.

Can I test firmware for the SmartRele without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.

Similar boards