DIY-Flipper-Repo
techzt13·DIY-Flipper-Repo·kicad/diy-flipper.kicad_pcb
About the DIY-Flipper-Repo PCB
DIY-Flipper-Repo is an open source PCB design by techzt13, published on GitHub. It is a 2-layer board measuring 125 × 135 mm, with 28 components from 18 distinct parts.
Other key parts include the SN74HC165N. By type, the board carries 10 connectors, 8 resistors, 7 switches, 1 IC, 1 transistor and 1 diode.
It belongs with the rf & radio, power & battery and dev boards & breakouts designs in this gallery.
From the project
My Hack Club Fallen project: a hand-built Flipper Zero clone based on the WeAct STM32WB55CGU6 board, running the official Flipper / Momentum firmware (via the open-source FCFZ / Nucleus Dark / Flipper-Diy community port). Remote participant — Hong Kong 🇭🇰
My Hack Club Fallen project: a hand-built Flipper Zero clone based on the WeAct STM32WB55CGU6 board, running the official Flipper / Momentum firmware (via the open-source FCFZ / Nucleus Dark / Flipper-Diy community port). Remote participant — Hong Kong 🇭🇰
Known clone limitations (firmware/secure-enclave, not fixable in hardware): U2F and KeeLoq need factory keys; 125 kHz RFID is not supported by the FCFZ firmware build; no speaker/vibration.

Main components on the DIY-Flipper-Repo
DIY-Flipper-Repo bill of materials (BOM)
28 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SN74HC165N | DIP-16_W7.62mm | U1 |
| 1 | 2N3904 | TO-92_Inline | Q1 |
| 1 | MCU top | PinHeader_1x14_P2.54mm_Vertical | J1 |
| 1 | MCU bottom (0.8/0.9/1.0in rows) | PinHeader_1x20_P2.54mm_Vertical_3row | J2 |
| 1 | ST7565 LCD | PinHeader_1x09_P2.54mm_Vertical | J3 |
| 1 | CC1101 | PinHeader_1x08_P2.54mm_Vertical | J4 |
| 1 | MicroSD | PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | NFC | PinHeader_1x07_P2.54mm_Vertical | J6 |
| 1 | IR-RX | PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | iButton | PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | UART | PinHeader_1x04_P2.54mm_Vertical | J9 |
| 1 | PWR | PinHeader_1x02_P2.54mm_Vertical | J10 |
| 6 | SW_Push | SW_PUSH_6mm | SW1, SW2, SW3, SW4, SW5, SW6 |
| 1 | SW_SPDT | SW_SPDT | SW7 |
| 1 | IR_LED | LED_D5.0mm | D1 |
| 6 | 10k | R_Axial_DIN0207_P7.62mm | R1, R2, R3, R4, R5, R6 |
| 1 | 1k | R_Axial_DIN0207_P7.62mm | R7 |
| 1 | 47R | R_Axial_DIN0207_P7.62mm | R8 |
DIY-Flipper-Repo design files
The KiCad project lives in the techzt13/DIY-Flipper-Repo repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad/diy-flipper.kicad_pcb
- Schematickicad/diy-flipper.kicad_sch
DIY-Flipper-Repo: common questions
How big is the DIY-Flipper-Repo PCB?
The DIY-Flipper-Repo measures 125 × 135 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the DIY-Flipper-Repo?
28 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the DIY-Flipper-Repo design files?
From the techzt13/DIY-Flipper-Repo repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the DIY-Flipper-Repo design in my own project?
The repository has no license, so all rights stay with techzt13. Use it as a reference, and ask the author before reusing the design.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2k