3we robot platform
telleroutlook·3we-robot-platform·hardware/pcb/robot-platform.kicad_pcb
About the 3we robot platform PCB
3we robot platform is an open source ESP32 PCB design by telleroutlook, published on GitHub under the Apache-2.0 license. It is a 4-layer board measuring 120 × 90 mm, with 4 components from 4 distinct parts.
Its main chip is the TB6612FNG, from the ESP32 family. By type, the board carries 3 connectors and 1 IC.
It belongs with the robotics & motion, sensors and power & battery designs in this gallery.
From the project
3we Universal Modular Mobile Robot Platform — Open-source firmware, ROS2, hardware, and SDK
The robot-platform mainboard integrates the ESP32-S3 MCU, motor drivers, power management, sensor interfaces, and the PBC-34 payload connector on a single 4-layer PCB.
- TPS3813 (U10): External watchdog, 1.6s timeout. GPIO46 toggles WDI; if firmware hangs, RST pulls ESP32 EN low → hardware reset. Independent of software watchdog. - Pi5 Power Switch (Q6a/Q6b/Q7): Dual Si2301CDS P-MOS (parallel, 5A total) with AO3400A N-MOS driver. GPIO45 HIGH = Pi5 ON. Default OFF at boot (R34 pull-down). Standard/Industrial SKU only (DNP on Basic). - E-stop Safety Path (SW1b → RLY1): The E-stop button has…
Main components on the 3we robot platform
3we robot platform bill of materials (BOM)
4 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TB6612FNG ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | XT60-MALE PBC-34_Payload_Bus | PBC-34 | J1 |
| 1 | JST-PH-6P XT30_Battery | XT30_Male_Vertical | J2 |
| 1 | JST-PH-6P USB_C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
3we robot platform design files
The KiCad project lives in the telleroutlook/3we-robot-platform repository on GitHub; these links point at the commit this page was built from.
3we robot platform: common questions
What microcontroller does the 3we robot platform use?
The 3we robot platform is built around the TB6612FNG, from the ESP32 family.
How big is the 3we robot platform PCB?
The 3we robot platform measures 120 × 90 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the 3we robot platform?
4 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the 3we robot platform design files?
From the telleroutlook/3we-robot-platform repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the 3we robot platform design in my own project?
Yes, under the terms of its Apache-2.0 license, which telleroutlook chose for the repository.
Can I test firmware for the 3we robot platform without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k