Tenn0-toolchanger board

Tenn0·tenn0-toolchanger-board

Tenn0-toolchanger board layout, top view — open source STM32 board by Tenn0

About the Tenn0-toolchanger board

Tenn0-toolchanger board is an open source STM32 PCB design by Tenn0, published on GitHub. It is a 2-layer board measuring 120 × 57.1 mm, with 49 components from 38 distinct parts.

Its main chip is the STM32G0B1CBTx, from the STM32 family. Other key parts include the SN65HVD1050D, ME6211C33M5, TPS5430DDA and USBLC6-2P6. By type, the board carries 16 capacitors, 9 resistors, 5 ICs, 5 connectors, 5 diodes and 3 inductors.

Main components on the Tenn0-toolchanger board

Tenn0-toolchanger board bill of materials (BOM)

49 components, 38 distinct parts.

QtyPartRefs
1
STM32G0B1CBTx
U1
1
SN65HVD1050D
U2
1
ME6211C33M5
U3
1
TPS5430DDA
U4
1
USBLC6-2P6
U5
1
Crystal_GND2
Y1
1
Conn_02x02_Odd_Even
J1
1
Cartographer
J2
1
Endstop1
J4
1
Endstop0
J5
1
USB_C_Plug
P1
1
0
5V_USB1
1
2A
F1
1
0
JP1_CAN1
1
BOOT0
SW1
1
RST
SW2
1
3V3
D1
2
SS24
D2, D4
1
B340
D3
1
MCU
D5
Show 18 more
QtyPartRefs
1
120Ohm 2A
FB1
1
22uH
L1
1
L_Coupled
L2
2
4.7uF
C1, C2
5
0.1uF
C3, C10, C13, C14, C15
1
0.01uF
C4
1
220 uF
C5
2
4.7 uF
C6, C7
2
100nF
C8, C9
2
15pF
C11, C12
1
100uF
C16
1
1.5K
R1
2
10k
R2, R5
1
3.24k
R3
1
120
R4
2
5.1k
R6, R7
1
10R
R8
1
1.5k
R9

Tenn0-toolchanger board design files

The KiCad project lives in the Tenn0/tenn0-toolchanger-board repository on GitHub; these links point at the commit this page was built from.

Tenn0-toolchanger board: common questions

What microcontroller does the Tenn0-toolchanger board use?

The Tenn0-toolchanger board is built around the STM32G0B1CBTx, from the STM32 family.

How big is the Tenn0-toolchanger board?

The Tenn0-toolchanger board measures 120 × 57.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Tenn0-toolchanger board?

49 components, from 38 distinct parts. The full bill of materials is listed on this page.

Where can I download the Tenn0-toolchanger board design files?

From the Tenn0/tenn0-toolchanger-board repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Tenn0-toolchanger board design in my own project?

The repository has no license, so all rights stay with Tenn0. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Tenn0-toolchanger board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards