Chytra budka
TeTeHacko·chytra-budka·firmware/hw/chytra-budka.kicad_sch
About the Chytra budka PCB
Chytra budka is an open source ESP32 PCB design by TeTeHacko, published on GitHub under the GPL-3.0 license. It is a board, with 16 components from 14 distinct parts.
Its main chip is the XIAO ESP32-S3 Sense, from the ESP32 family. Other key parts include the WaveShare SolarPMS, MAX17048 breakout and SHT41-AD1B. By type, the board carries 5 connectors, 4 ICs, 3 resistors, 2 capacitors, 1 transistor and 1 diode.
It belongs with the iot & wireless, power & battery and sensors designs in this gallery.
From the project
Solar-ready ESP32-S3 wildlife camera/mic box — BirdNET audio ID, MQTT + Home Assistant, per-device HTTPS enrollment, signed OTA, self-hostable server stack
KiCad 10 project + automation via KiKit.
The bill of materials (parts, search terms, and prices) lives in one place: SHOPPING.md. This doc covers the PCB/schematic side only. The carrier-PCB parts (MAX17048, SHT41, passives, JST) are listed under SHOPPING.md's Optional — custom carrier PCB section.
What changed vs rev3.1: D8/D9/D10 (GPIO 7/8/9) were planned in rev3.1 for an external INMP441 over I²S. In rev3.2 that external mic was dropped (pin conflict with the onboard SDIO microSD) and these pins are hard-wired to the microSD slot on the Sense expansion — don't connect anything external…
Main components on the Chytra budka
Chytra budka bill of materials (BOM)
16 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO ESP32-S3 Sense | U1 | |
| 1 | WaveShare SolarPMS | U2 | |
| 1 | MAX17048 breakout | U3 | |
| 1 | SHT41-AD1B | U4 | |
| 1 | AO3400 | Q1 | |
| 1 | DC Solar 18V | J1 | |
| 1 | 2x18650 1S2P PCM | J2 | |
| 1 | INMP441 mic | J3 | |
| 1 | AM312 PIR | J4 | |
| 1 | IR LED 940nm | J5 | |
| 1 | 1N4148 | D1 | |
| 2 | 100nF | C1, C2 | |
| 2 | 10k | R1, R2 | |
| 1 | 220R/0.5W | R3 |
Chytra budka design files
The KiCad project lives in the TeTeHacko/chytra-budka repository on GitHub; these links point at the commit this page was built from.
- Schematicfirmware/hw/chytra-budka.kicad_sch
Chytra budka: common questions
What microcontroller does the Chytra budka use?
The Chytra budka is built around the XIAO ESP32-S3 Sense, from the ESP32 family.
How many components are on the Chytra budka?
16 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Chytra budka design files?
From the TeTeHacko/chytra-budka repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Chytra budka design in my own project?
Yes, under the terms of its GPL-3.0 license, which TeTeHacko chose for the repository.
Can I test firmware for the Chytra budka without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k