Kokoromi
tetra-mix·kokoromi·electric/kokoromi.kicad_pcb
About the Kokoromi PCB
Kokoromi is an open source AVR/Arduino PCB design by tetra-mix, published on GitHub. It is a 2-layer board measuring 27 × 27 mm, with 18 components from 12 distinct parts.
Its main chip is the ATmega328-M, from the AVR/Arduino family. Other key parts include the CH340K, LIS2DH and XC6206PxxxMR. By type, the board carries 6 connectors, 4 ICs, 4 capacitors, 3 resistors and 1 switch.
Main components on the Kokoromi
Kokoromi bill of materials (BOM)
18 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH340K | SSOP-10-1EP_3.9x4.9mm_P1mm_EP2.1x3.3mm | U1 |
| 1 | LIS2DH | LGA-14_2x2mm_P0.35mm_LayoutBorder3x4y | U3 |
| 1 | ATmega328-M | QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U4 |
| 1 | XC6206PxxxMR | SOT-23-3 | U5 |
| 1 | Conn_01x02_Socket | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J1 |
| 4 | Conn_01x04_Pin | PinSocket_2x02_P1.27mm_Vertical | J2, J3, J4, J5 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J6 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 3 | 10uF | C_0805_2012Metric | C1, C3, C4 |
| 1 | 0.1uF | C_0805_2012Metric | C2 |
| 1 | 10k | R_0805_2012Metric | R1 |
| 2 | 5.1k | R_0603_1608Metric | R2, R3 |
Kokoromi design files
The KiCad project lives in the tetra-mix/kokoromi repository on GitHub; these links point at the commit this page was built from.
- Layoutelectric/kokoromi.kicad_pcb
- Schematicelectric/kokoromi.kicad_sch
Kokoromi: common questions
What microcontroller does the Kokoromi use?
The Kokoromi is built around the ATmega328-M, from the AVR/Arduino family.
How big is the Kokoromi PCB?
The Kokoromi measures 27 × 27 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Kokoromi?
18 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Kokoromi design files?
From the tetra-mix/kokoromi repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Kokoromi design in my own project?
The repository has no license, so all rights stay with tetra-mix. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Kokoromi without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k