21 open source boards using the LIS2DH

Real designs built with the LIS2DH, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

21 boardsClear filters|Most starred

How designs wire the LIS2DH

Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the LIS2DH connects to, and the resistors, capacitors and other passives placed on it.

  • The SCL/SPC pin has a pull-up to 3.3V on 12 of 19 designs, most often 5.1 kΩ (then 4.7 kΩ).
  • The VDD_IO pin has a decoupling capacitor on 12 of 19 designs, most often 100 nF (then 470 nF).
  • The VDD pin has a decoupling capacitor on 12 of 19 designs, most often 100 nF (then 470 nF).
  • The SDA/SDI pin has a pull-up to 3.3V on 11 of 19 designs, most often 5.1 kΩ (then 4.7 kΩ).
SCL/SPCpin 1Connected to: The microcontroller 37%, MSPM0G3507SPTR 26%, a connector 21%
  • Pull-up to 3.3V on 63% · 5.1 kΩ (7), 4.7 kΩ (3), 10 kΩ (2)
SDA/SDIpin 2Connected to: The microcontroller 26%, MSPM0G3507SPTR 26%, a connector 21%
  • Pull-up to 3.3V on 58% · 5.1 kΩ (7), 4.7 kΩ (2), 100 kΩ (1)
SDOpin 3Connected to: GND 63% · a signal 26%
VDD_IOpin 7Connected to: 3.3V 74% · GND 21%
  • Decoupling capacitor on 63% · 100 nF (8), 470 nF (6), 1 µF (3)
VDDpin 8Connected to: 3.3V 74% · GND 21%
  • Decoupling capacitor on 63% · 100 nF (8), 470 nF (6), 1 µF (4)
GNDpin 9, 10, 11, 12, 13, 14Connected to: GND 65% · not connected 16%

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Elixir hw by golioth, Hourglass revb by geschmit, Hw by minddot and Sidewalk Devkit by hlord2000.

The LIS2DH in open source designs

The gallery holds 21 open source boards using the LIS2DH from 20 GitHub repositories; a typical one measures about 53.5 × 34 mm and carries around 57 components.

57% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.

The most starred is Tinypulse by jonnor.

Microcontrollers on boards using the LIS2DH

LIS2DH: common questions

Where can I find a LIS2DH reference design?

Each of the 21 boards on this page is a real design using the LIS2DH. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the LIS2DH SCL/SPC pin?

The SCL/SPC pin has a pull-up to 3.3V on 12 of 19 designs, most often 5.1 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 19 open source designs using the LIS2DH.

What decoupling capacitors do designs use on the LIS2DH VDD_IO pin?

The VDD_IO pin has a decoupling capacitor on 12 of 19 designs, most often 100 nF (then 470 nF). Counted from the KiCad layouts of 19 open source designs using the LIS2DH.

What decoupling capacitors do designs use on the LIS2DH VDD pin?

The VDD pin has a decoupling capacitor on 12 of 19 designs, most often 100 nF (then 470 nF). Counted from the KiCad layouts of 19 open source designs using the LIS2DH.

What parts are used alongside the LIS2DH?

The CH340E, SPX3819M5-L-3-3, MSPM0G3507SPTR, BME280 and USBLC6-2SC6 appear in the most repositories here.

Which microcontrollers do boards using the LIS2DH use?

Most are built on ESP32 (4), Nordic nRF (4), AVR/Arduino (2) and RP2040/RP2350 (2).

How big is a typical board using the LIS2DH?

The median is 53.5 × 34 mm, and 57% are two-layer designs.

What is the most popular open source board using the LIS2DH?

By GitHub stars, Tinypulse by jonnor, with 315 stars.

Can I simulate one of these boards using the LIS2DH before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part