Atmega demo
timdrysdale·atmega-demo·pcb/atmega-demo/atmega-demo.kicad_pcb
About the Atmega demo PCB
Atmega demo is an open source AVR/Arduino PCB design by timdrysdale, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 69.6 × 20.8 mm, with 36 components from 25 distinct parts.
Its main chip is the ATmega328P-AU, from the AVR/Arduino family. Other key parts include the ACS712xLCTR-20A, MCP9700T-HTT and CH340G. By type, the board carries 12 capacitors, 5 test points, 4 ICs, 4 connectors, 4 resistors and 3 diodes.
It belongs with the sensors designs in this gallery.
From the project
PCB to demonstrate atmega microcontroller
This board will be used to monitor power consumption and temperature in remote lab boxes.
The key components are an Atmega328P, a CH340 USB transceiver, an ACS712 current sensor and a simple analog temperature sensor. DTR reset is enabled to support re-programming over USB, while ICSP header is supplied for initial programming. Both CH340 and Atmega are using 12MHz crystals, which yields 0.1% baud rate error at 57600 baud for the Atmega.

Main components on the Atmega demo
Atmega demo bill of materials (BOM)
36 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ACS712xLCTR-20A | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | MCP9700T-HTT | SOT-23 | U2 |
| 1 | ATmega328P-AU | TQFP-32_7x7mm_P0.8mm | U3 |
| 1 | CH340G | SOIC-16_3.9x9.9mm_P1.27mm | U4 |
| 2 | 12MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1, Y2 |
| 1 | Conn_01x04_Male | PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | AVR_ICSP | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | USB_B_Micro | USB_Micro-B_Amphenol_10118194_Horizontal | J3 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_bornier-2_P5.08mm | J4 |
| 1 | NO | SW_SPST_PTS810 | SW1 |
| 5 | TestPoint | TestPoint_Keystone_5015_Micro-Minature | TP1, TP2, TP3, TP4, TP5 |
| 1 | Green | LED_0603_1608Metric | D1 |
| 1 | Blue | LED_0603_1608Metric | D2 |
| 1 | PRTR5V0U2X | SOT-143 | D3 |
| 1 | 10u | L_0805_2012Metric | L1 |
| 1 | 0.1n | C_0603_1608Metric | C1 |
| 2 | 0.1u | C_0603_1608Metric | C2, C3 |
| 1 | 100n | C_0805_2012Metric | C4 |
| 2 | 22p | C_0603_1608Metric | C5, C6 |
| 1 | 4n7 | C_0603_1608Metric | C7 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 100n | C_0603_1608Metric | C8, C11, C12 |
| 2 | 33p | C_0603_1608Metric | C9, C10 |
| 1 | 10K | R_0603_1608Metric | R1 |
| 2 | 68 | R_0603_1608Metric | R2, R3 |
| 1 | 1M | R_0603_1608Metric | R4 |
Atmega demo design files
The KiCad project lives in the timdrysdale/atmega-demo repository on GitHub; these links point at the commit this page was built from.
Atmega demo: common questions
What microcontroller does the Atmega demo use?
The Atmega demo is built around the ATmega328P-AU, from the AVR/Arduino family.
How big is the Atmega demo PCB?
The Atmega demo measures 69.6 × 20.8 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Atmega demo?
36 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the Atmega demo design files?
From the timdrysdale/atmega-demo repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Atmega demo design in my own project?
Yes, under the terms of its GPL-3.0 license, which timdrysdale chose for the repository.
Can I test firmware for the Atmega demo without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k