19 open source boards using the ACS712xLCTR-20A
Real designs built with the ACS712xLCTR-20A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Expansion board
reubenstr
100 × 49.8 mm75 parts4LMIT51STM32
MVCU F407
Vaaarad07
132.9 × 108.4 mm100 parts4LMIT10Cell holder board
tjorvenhillmann
101 × 101 mm52 parts2LNo license5ESP32
PCB V2
BhoumikAcharya
94.5 × 75.6 mm161 parts2LNo license1STM32
BDSM G144
matatma23-gento
247.9 × 172.6 mm304 parts4LNo license0STM32
Arachne
TheColonelYoung
100 × 70 mm265 parts2LGPL-3.00FOC INVERTER
Abdelrahman-Elnahrawy
245.4 × 77.5 mm132 parts2LGPL-3.00Chb inverter
feaksel
209.6 × 120.7 mm95 parts2LApache-2.00STM32
Backup
DoloresAx
85.1 × 55.9 mm78 parts2LNo license0AVR/Arduino
NeptuneESC
15jgme
50 × 29 mm60 parts2LLGPL-3.00AVR/Arduino
Rpi-GC-Oven-Controller
Pharmaceutical-Analysis
120 × 100 mm58 parts2LNo license0AVR/Arduino
Atmega demo
timdrysdale
69.6 × 20.8 mm36 parts4LGPL-3.00ESP32
AccessController
minsk-hackerspace
75.6 × 81.9 mm33 parts2LNo license0NXP
Motor controller
reubenstr
100 × 40 mm63 parts4LMIT51STM32
Projecting
DoloresAx
85.1 × 55.9 mm78 parts2LNo license0VP44expSwdriver
Greatwrk
50 × 100 mm47 parts2LMIT9STM32
VCU
Vaaarad07
81.8 × 80.2 mm71 parts2LMIT10HBM G0V48C15
Omar-Magdy0
32.2 × 69.6 mm37 parts2LMIT0ACS712
BhoumikAcharya
10.9 × 15.2 mm6 parts2LNo license1
How designs wire the ACS712xLCTR-20A
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the ACS712xLCTR-20A connects to, and the resistors, capacitors and other passives placed on it.
- The FILTER pin has a capacitor to GND on 13 of 15 designs, most often 1 nF (then 100 nF).
- The VIOUT pin has a series resistor on 9 of 15 designs, most often 10 kΩ (then 1.5 kΩ).
- The VCC pin has a decoupling capacitor on 8 of 15 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 5 | Connected to: GND 93% | — |
| FILTERpin 6 | Connected to: Signal 93% |
|
| VIOUTpin 7 | Connected to: The microcontroller 20% |
|
| VCCpin 8 | Connected to: 5V 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Expansion board by reubenstr, MVCU F407 by Vaaarad07, VP44expSwdriver by Greatwrk and Cell holder board by tjorvenhillmann.
The ACS712xLCTR-20A in open source designs
The gallery holds 19 open source boards using the ACS712xLCTR-20A from 15 GitHub repositories; a typical one measures about 94.5 × 75.6 mm and carries around 71 components.
74% are two-layer designs, the rest use four layers or more, and 58% carry an open source license.
The most starred is Expansion board by reubenstr.
Parts used alongside the ACS712xLCTR-20A
Microcontrollers on boards using the ACS712xLCTR-20A
What boards using the ACS712xLCTR-20A are built for
ACS712xLCTR-20A: common questions
Where can I find a ACS712xLCTR-20A reference design?
Each of the 19 boards on this page is a real design using the ACS712xLCTR-20A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ACS712xLCTR-20A FILTER pin connected?
The FILTER pin has a capacitor to GND on 13 of 15 designs, most often 1 nF (then 100 nF). Counted from the KiCad layouts of 15 open source designs using the ACS712xLCTR-20A.
What resistor goes on the ACS712xLCTR-20A VIOUT pin?
The VIOUT pin has a series resistor on 9 of 15 designs, most often 10 kΩ (then 1.5 kΩ). Counted from the KiCad layouts of 15 open source designs using the ACS712xLCTR-20A.
What decoupling capacitors do designs use on the ACS712xLCTR-20A VCC pin?
The VCC pin has a decoupling capacitor on 8 of 15 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 15 open source designs using the ACS712xLCTR-20A.
What parts are used alongside the ACS712xLCTR-20A?
The AMS1117-3.3, AMS1117-5.0, LM2596S-5, LM7805_TO220 and MCP2551-I-SN appear in the most repositories here.
Which microcontrollers do boards using the ACS712xLCTR-20A use?
Most are built on STM32 (6), AVR/Arduino (3), ESP32 (2) and NXP (1).
How big is a typical board using the ACS712xLCTR-20A?
The median is 94.5 × 75.6 mm, and 74% are two-layer designs.
What is the most popular open source board using the ACS712xLCTR-20A?
By GitHub stars, Expansion board by reubenstr, with 51 stars.
Can I simulate one of these boards using the ACS712xLCTR-20A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.