DDR3L-tester
TomasD-git·DDR3L-tester·DDR3 tester/DDR3 tester.kicad_pcb
About the DDR3L-tester PCB
DDR3L-tester is an open source ESP32 PCB design by TomasD-git, published on GitHub under the MIT license. It is a 2-layer board measuring 91.3 × 69.8 mm, with 37 components from 21 distinct parts.
Its main chip is the ESP32-C6-MINI-1/U, from the ESP32 family. Other key parts include the XDAP-4042044-20401 and AP2112K-3.3TRG1. By type, the board carries 13 capacitors, 11 resistors, 6 switches, 3 ICs, 2 diodes and 1 connector.
From the project
Very simple DDR3L tester, plug ddr3l stick into slot, esp32 c6 reads data and can overwrite config as well
Either buy PCBA which is much easier but much more expenisve, or buy all parts and assemble with hotplate or hotair gun. all files needed for this are in production folder
Main components on the DDR3L-tester
DDR3L-tester bill of materials (BOM)
37 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XDAP-4042044-20401 LX(连欣科技) | CONN-SMD_204P-P0.60_XDAP-4042044-20401 | U2 |
| 1 | AP2112K-3.3TRG1 DIODES(美台) | SOT-25-5_L2.9-W1.6-P0.95-LS2.8-BL | U3 |
| 1 | ESP32-C6-MINI-1/U | ESP32-C6-MINI-1 | U4 |
| 1 | 128x64 LCD Display | PinSocket_1x04_P2.54mm_Vertical | J1 |
| 2 | SW_Push | SW_PUSH_6mm | SW1, SW2 |
| 1 | RotaryEncoder_Switch_MP | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW3 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW4, SW5 |
| 1 | SS-12D00-G 4 E | 1P2T_SS-12D00_CNK | SW6 |
| 1 | TYPE-C 16PIN 2MD(073) TYPE-C 16PIN 2MD SHOU HAN(首韩) | USB-C-SMD_TYPE-C-16PIN-2MD-073 | USB1 |
| 1 | GREEN LED | LED_D5.0mm | D1 |
| 1 | RED LED | LED_D5.0mm | D2 |
| 5 | 100nF | C_0805_2012Metric | C1, C5, C10, C19, C20 |
| 1 | 47uF | C_1210_3225Metric | C2 |
| 2 | 10uF | C_0805_2012Metric | C3, C7 |
| 3 | 1uF | C_0805_2012Metric | C4, C6, C21 |
| 2 | 1nF | C_0805_2012Metric | C8, C9 |
| 3 | 10K | R_0805_2012Metric | R1, R9, R10 |
| 2 | 330 | R_0805_2012Metric | R2, R3 |
| 2 | 22 | R_0805_2012Metric | R11, R12 |
| 2 | 5.1K | R_0805_2012Metric | R13, R14 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 4.7K | R_0805_2012Metric | R15, R16 |
DDR3L-tester design files
The KiCad project lives in the TomasD-git/DDR3L-tester repository on GitHub; these links point at the commit this page was built from.
DDR3L-tester: common questions
What microcontroller does the DDR3L-tester use?
The DDR3L-tester is built around the ESP32-C6-MINI-1/U, from the ESP32 family.
How big is the DDR3L-tester PCB?
The DDR3L-tester measures 91.3 × 69.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the DDR3L-tester?
37 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the DDR3L-tester design files?
From the TomasD-git/DDR3L-tester repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the DDR3L-tester design in my own project?
Yes, under the terms of its MIT license, which TomasD-git chose for the repository.
Can I test firmware for the DDR3L-tester without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k