29 open source boards using the ESP32-C6-MINI-1/U
Real designs built with the ESP32-C6-MINI-1/U, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Co2-canary
blinry
61 × 61 mm50 parts2LNo license78ESP32
Minuet Fan Controller
brown-studios
79 × 79 mm87 parts4LMIT65ESP32
MiniCO2
nup002
13.6 × 19.4 mm25 parts4LNo license40ESP32
ZigBee SmartMeter Reader
Tropaion
43.3 × 37.6 mm36 parts2LGPL-3.032ESP32
A0 IoT GATEWAY
absmach
54.6 × 86.3 mm57 parts4LApache-2.016ESP32
Wisweep
slimcdk
38.5 × 39.2 mm54 parts4LMIT14ESP32
Riskybirdv3
ucb-bar
58.3 × 58.3 mm172 parts4LNo license2ESP32
VCAT-VehicleControlUnit
lhr-solar
86.6 × 71.8 mm122 parts2LMIT2ESP32
Multical eye
slimcdk
38.5 × 39.6 mm59 parts4LMIT2ESP32
OpenTRV-ESP
mpiraux
45 × 53 mm58 parts4LCERN-OHL-P-2.02ESP32
BeeFASYER SPARROW
beewarden
64.1 × 72.8 mm121 parts4LCERN-OHL-S-2.01ESP32
KIA-OBD2-DISPLAY
dragonnn
99.8 × 19.6 mm72 parts4LMIT1ESP32
Pb-Monitor v2
ElektorLabs
68.4 × 51.1 mm68 parts2LGPL-3.01ESP32
Pager
ambraglow
116.4 × 55.3 mm59 parts2LGPL-3.01ESP32
In13-nixie device
nonik0
38.1 × 43.1 mm29 parts2LNo license1ESP32
Aaram
xicor22
100 × 100 mm77 parts2LGPL-3.00ESP32
AHAQ-1
vactomas
50 × 50 mm58 parts4LNo license0ESP32
DDR3L-tester
TomasD-git
91.3 × 69.8 mm37 parts2LMIT0ESP32
OpenESPTemp
mawaeg
15 × 63 mm34 parts2LGPL-3.00ESP32
Liquid simulator
TomasD-git
38 × 45.5 mm30 parts2LNo license0ESP32
Esp32-ble sensor
philipcristiano
27.5 × 89 mm29 parts2LNo license0ESP32
Avi hw mesh node
Apoll011
32 × 30 mm27 parts2LMIT0ESP32
IoTLynx
halherta
38 × 58 mm23 parts2LNo license0ESP32
Open-Source-Temperature-Sensor-ESP32-C6
IN4148
30 × 28 mm22 parts2LNo license0ESP32
Windlink
connorslade
36 × 26 mm20 parts2LNo license0ESP32
Arctic-Fox-Light
Cherrytree56567
32 × 38.5 mm17 parts2LNo license0- schematic only · 67 partsESP32
NodeHealthMonitor
aniketdebnath
67 partsMIT0 ESP32
Riskybirdv2 esp
ucb-bar
24 × 39 mm39 parts2LNo license2ESP32
Mk2Wifi-C6
FredM67
51 × 26.3 mm23 parts2LCC-BY-SA-4.00
How designs wire the ESP32-C6-MINI-1/U
Read from the KiCad layouts of 27 open source designs, one per repository: what each pin of the ESP32-C6-MINI-1/U connects to, and the resistors, capacitors and other passives placed on it.
- The EN/CHIP_PU pin has a pull-up to 3.3V on 23 of 27 designs, most often 10 kΩ (then 5.1 kΩ).
- The 3V3 pin is tied to 3.3V on 27 of 27 designs.
- The EN/CHIP_PU pin has a capacitor to GND on 22 of 27 designs, most often 1 µF (then 100 nF).
- The GPIO8 pin has a pull-up to 3.3V on 15 of 27 designs, most often 10 kΩ (then 3.3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 2, 11, 14, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53 | Connected to: GND 96% | — |
| 3V3pin 3 | Connected to: 3.3V 100% | — |
| NCpin 4, 7, 21, 32, 33, 34, 35 | Connected to: Not connected 100% | — |
| EN/CHIP_PUpin 8 | Connected to: Signal 85% |
|
| GPIO8pin 22 | Connected to: Signal 74% · not connected 22% |
|
| GPIO9pin 23 | Connected to: Signal 89% |
|
20 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Co2-canary by blinry, Minuet Fan Controller by brown-studios, MiniCO2 by nup002 and ZigBee SmartMeter Reader by Tropaion.
The ESP32-C6-MINI-1/U in open source designs
The gallery holds 29 open source boards using the ESP32-C6-MINI-1/U from 28 GitHub repositories; a typical one measures about 44.2 × 50.6 mm and carries around 50 components.
64% are two-layer designs, the rest use four layers or more, and 59% carry an open source license.
The most starred is Co2-canary by blinry.
Parts used alongside the ESP32-C6-MINI-1/U
Microcontrollers on boards using the ESP32-C6-MINI-1/U
What boards using the ESP32-C6-MINI-1/U are built for
ESP32-C6-MINI-1/U: common questions
Where can I find a ESP32-C6-MINI-1/U reference design?
Each of the 29 boards on this page is a real design using the ESP32-C6-MINI-1/U. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP32-C6-MINI-1/U EN/CHIP_PU pin?
The EN/CHIP_PU pin has a pull-up to 3.3V on 23 of 27 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 27 open source designs using the ESP32-C6-MINI-1/U.
How is the ESP32-C6-MINI-1/U 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 27 of 27 designs. Counted from the KiCad layouts of 27 open source designs using the ESP32-C6-MINI-1/U.
What pull-up resistor is used on the ESP32-C6-MINI-1/U GPIO8 pin?
The GPIO8 pin has a pull-up to 3.3V on 15 of 27 designs, most often 10 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 27 open source designs using the ESP32-C6-MINI-1/U.
What parts are used alongside the ESP32-C6-MINI-1/U?
The AP2112K-3.3, MCP73831-2-OT, AMS1117-3.3, AS5047D and LMR16006YQ3 appear in the most repositories here.
Which microcontrollers do boards using the ESP32-C6-MINI-1/U use?
Most are built on ESP32 (29).
How big is a typical board using the ESP32-C6-MINI-1/U?
The median is 44.2 × 50.6 mm, and 64% are two-layer designs.
What is the most popular open source board using the ESP32-C6-MINI-1/U?
By GitHub stars, Co2-canary by blinry, with 78 stars.
Can I simulate one of these boards using the ESP32-C6-MINI-1/U before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.