MacroPad-V2
TomasD-git·MacroPad-V2·KiCad/New macropad.kicad_pcb
About the MacroPad-V2 PCB
MacroPad-V2 is an open source ESP32 PCB design by TomasD-git, published on GitHub. It is a 2-layer board measuring 84.5 × 112.8 mm, with 34 components from 4 distinct parts.
Its main chip is the XIAO-ESP32-C3-DIP, from the ESP32 family. By type, the board carries 17 switches, 16 diodes and 1 IC.
It belongs with the keyboards and power & battery designs in this gallery.
From the project
a new deisgn for macropad, 16 macro keys with rotary encoder, planning on adding battery
Main components on the MacroPad-V2
MacroPad-V2 bill of materials (BOM)
34 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-DIP | Xiao_rp2040_AH_Pogo | U1 |
| 16 | SW_Push | SW_Cherry_MX_PCB_1.00u | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +8 |
| 1 | SS-12D00-G 4 E | 1P2T_SS-12D00_CNK | SW17 |
| 16 | 1N4148WT | D_SOD-123 | D1, D2, D3, D4, D5, D6, D7, D8 +8 |
MacroPad-V2 design files
The KiCad project lives in the TomasD-git/MacroPad-V2 repository on GitHub; these links point at the commit this page was built from.
MacroPad-V2: common questions
What microcontroller does the MacroPad-V2 use?
The MacroPad-V2 is built around the XIAO-ESP32-C3-DIP, from the ESP32 family.
How big is the MacroPad-V2 PCB?
The MacroPad-V2 measures 84.5 × 112.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MacroPad-V2?
34 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MacroPad-V2 design files?
From the TomasD-git/MacroPad-V2 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the MacroPad-V2 design in my own project?
The repository has no license, so all rights stay with TomasD-git. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the MacroPad-V2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k