Fordacp LCD
About the Fordacp LCD PCB
Fordacp LCD is an open source AVR/Arduino PCB design by tomaskovacik, published on GitHub. It is a 2-layer board measuring 81.9 × 42.4 mm, with 35 components from 25 distinct parts.
Its main chip is the ATMEGA2560-A, from the AVR/Arduino family. Other key parts include the SP3485CN, AP1117D50, BLK-MD-SPK-B and XS3860. By type, the board carries 11 capacitors, 9 resistors, 5 ICs, 3 diodes, 1 crystal and 1 connector.
It belongs with the displays & leds designs in this gallery.
From the project
HW for Dale Thomas fordcap CD changer emualtor
SW is Dale Thomas/Krzysztof Pintscher/Andrew Hammond work not my
www.instructables.com/id/Ford-CD-Emulator-Arduino-Mega/ http://www.instructables.com/id/Ford-Bluetooth-Interface-Control-phone-with-stock-/
I make just HW part in kicad, libraries for BLK-MD-SPK-B and S3860M-S here
schematics ------------ schematics in pdf
Main components on the Fordacp LCD
Fordacp LCD bill of materials (BOM)
35 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA2560-A | TQFP-100_14x14mm_Pitch0.5mm | IC1 |
| 1 | SP3485CN | SO-8 | U1 |
| 1 | AP1117D50 | SOT-223-REGULATOR | U2 |
| 1 | BLK-MD-SPK-B | BLK-MD-SPK-B | U3 |
| 1 | XS3860 | S3860M-S | U4 |
| 1 | 16MHz | Q_49U3HMS | Y1 |
| 1 | CONN_02X06 | Pin_Header_Straight_2x06 | P1 |
| 1 | LCD-016N002L | WC1602A | DS1 |
| 2 | CONN_01X02 | Pin_Header_Straight_1x02 | MIC1, programing1 |
| 1 | 1k | Potentiometer_Bourns_3339H_Angular_ScrewUp | RV1 |
| 1 | GREEN | LED-1206 | D1 |
| 1 | RED | LED-1206 | D2 |
| 1 | 5V1 | MiniMELF_Standard | D3 |
| 1 | 15nH | SMD-1206_Pol | L1 |
| 1 | 47u/25V | TantalC_SizeD_EIA-7343_HandSoldering | C1 |
| 6 | 100n/50V | C_1206_HandSoldering | C2, C5, C6, C7, C8, C9 |
| 1 | 1uf/10V | c_elec_4x5.3 | C3 |
| 1 | 4u7/10V | c_elec_5x5.3 | C4 |
| 2 | 2u2/10V | c_elec_5x5.3 | C10, C11 |
| 1 | 2k7 | R_0805_HandSoldering | R1 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1M | R_0805_HandSoldering | R2 |
| 1 | 27R | R_0805_HandSoldering | R3 |
| 2 | 470 | R_0805_HandSoldering | R4, R5 |
| 1 | 6k8 | R_0805_HandSoldering | R6 |
| 3 | 4k7 | R_0805_HandSoldering | R7, R8, R9 |
Fordacp LCD design files
The KiCad project lives in the tomaskovacik/fordacp repository on GitHub; these links point at the commit this page was built from.
- Layouthw/fordacp_LCD.kicad_pcb
Fordacp LCD: common questions
What microcontroller does the Fordacp LCD use?
The Fordacp LCD is built around the ATMEGA2560-A, from the AVR/Arduino family.
How big is the Fordacp LCD PCB?
The Fordacp LCD measures 81.9 × 42.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Fordacp LCD?
35 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the Fordacp LCD design files?
From the tomaskovacik/fordacp repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Fordacp LCD design in my own project?
The repository has no license, so all rights stay with tomaskovacik. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Fordacp LCD without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in fordacp
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoV4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoModuleV450
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k