TrailCurrentTherma
trailcurrentoss·TrailCurrentTherma·EDA/TrailCurrentTherma/TrailCurrentTherma.kicad_pcb
About the TrailCurrentTherma PCB
TrailCurrentTherma is an open source ESP32 PCB design by trailcurrentoss, published on GitHub under the MIT license. It is a 2-layer board measuring 56.4 × 64.2 mm, with 8 components from 8 distinct parts.
Its main chip is the ESP32-C6-Super-Mini, from the ESP32 family. Other key parts include the Amazon Buck Converter, SN65HVD230 and ZX-XH2.54-4PWT. By type, the board carries 4 ICs, 2 resistors, 1 connector and 1 capacitor.
It belongs with the iot & wireless designs in this gallery.
From the project
This repository contains the EDA, CAD and firmware for a electic heater control for the TrailCurrent platform
Closed-loop thermostat for the TrailCurrent open-source vehicle platform. ESP-IDF firmware. Three boards, three firmware artifacts, one purpose.
Therma is built from three ESP32-S3 boards. Only the first board is on the CAN bus; the other two are driven from the first over direct GPIO wires.
- Therma Controller — Waveshare ESP32-S3-RS485-CAN (same module as Bearing). Only board on the CAN bus. Authoritative owner of: - Desired temperature (setpoint) - Hysteresis threshold (deadband) - Current heat/cool mode Persists setpoint and threshold to NVS so a power cycle preserves them. Consumes…
Main components on the TrailCurrentTherma
TrailCurrentTherma bill of materials (BOM)
8 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Amazon Buck Converter | AmazonBuckConverter | U1 |
| 1 | ESP32-C6-Super-Mini | ESP32-C6-Super-Mini | U2 |
| 1 | SN65HVD230 | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | ZX-XH2.54-4PWT | CONN-SMD_4P-P2.50-WAFER-254W-4P | U4 |
| 1 | DHT22 | PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | 100nF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 1 | 10k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 1 | 4.7K | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | R2 |
TrailCurrentTherma design files
The KiCad project lives in the trailcurrentoss/TrailCurrentTherma repository on GitHub; these links point at the commit this page was built from.
TrailCurrentTherma: common questions
What microcontroller does the TrailCurrentTherma use?
The TrailCurrentTherma is built around the ESP32-C6-Super-Mini, from the ESP32 family.
How big is the TrailCurrentTherma PCB?
The TrailCurrentTherma measures 56.4 × 64.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the TrailCurrentTherma?
8 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the TrailCurrentTherma design files?
From the trailcurrentoss/TrailCurrentTherma repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the TrailCurrentTherma design in my own project?
Yes, under the terms of its MIT license, which trailcurrentoss chose for the repository.
Can I test firmware for the TrailCurrentTherma without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k