FLT ART CU1 Multicart
trwgQ26xxx·FLT_ART_CU1_Multicart·PCB/tiny806_version/Multicart.kicad_pcb
About the FLT ART CU1 Multicart PCB
FLT ART CU1 Multicart is an open source AVR/Arduino PCB design by trwgQ26xxx, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 78 × 90 mm, with 38 components from 16 distinct parts.
Its main chip is the ATtiny806-S, from the AVR/Arduino family. Other key parts include the 74HC00, 74LS573, SST39SF040 and SA39-11SRWA. By type, the board carries 15 resistors, 12 capacitors, 7 ICs, 2 switches, 1 transistor and 1 connector.
From the project
Multicart for Fiat Lancia Tester\Alfa Romeo Tester\Check Up 1
A multicart ROM module that replaces eight standard FLT modules. It contains eight ROM sets stored in a 512kB (4Mbit) flash memory, which can be switched on the fly.
Two variants are implemented: one using an Atmel AT89C2051 MCU (revisions A - green and B - blue), and another based on a Microchip ATtiny806 (revision C - yellow).
I do not consent to the use of all or part of the project for commercial purposes!

Main components on the FLT ART CU1 Multicart
FLT ART CU1 Multicart bill of materials (BOM)
38 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 74HC00 | SOIC-14_3.9x8.7mm_P1.27mm | U1 |
| 1 | 74LS573 | SOIC-20W_7.5x12.8mm_P1.27mm | U2 |
| 3 | SST39SF040 | PLCC-32_11.4x14.0mm_P1.27mm | U3, U4, U5 |
| 1 | ATtiny806-S | SOIC-20W_7.5x12.8mm_P1.27mm | U6 |
| 1 | SA39-11SRWA | Sx39-1xxxxx | U7 |
| 1 | BC817 | SOT-23_Handsoldering | Q1 |
| 1 | PROG | PinHeader_1x03_P2.54mm_Horizontal | J2 |
| 1 | BACK | SW_PUSH_6mm | SW1 |
| 1 | NEXT | SW_PUSH_6mm | SW2 |
| 11 | 100n | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2, C3, C4, C5, C6, C7, C8 +3 |
| 1 | DNP | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C12 |
| 8 | 1k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2, R3, R6, R7, R8, R12, R13 |
| 2 | 10k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4, R5 |
| 3 | 330 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R9, R10, R11 |
| 1 | 4k7 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R14 |
| 1 | DNP | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R15 |
FLT ART CU1 Multicart design files
The KiCad project lives in the trwgQ26xxx/FLT_ART_CU1_Multicart repository on GitHub; these links point at the commit this page was built from.
FLT ART CU1 Multicart: common questions
What microcontroller does the FLT ART CU1 Multicart use?
The FLT ART CU1 Multicart is built around the ATtiny806-S, from the AVR/Arduino family.
How big is the FLT ART CU1 Multicart PCB?
The FLT ART CU1 Multicart measures 78 × 90 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the FLT ART CU1 Multicart?
38 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the FLT ART CU1 Multicart design files?
From the trwgQ26xxx/FLT_ART_CU1_Multicart repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the FLT ART CU1 Multicart design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the FLT ART CU1 Multicart without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k